Difference between revisions of "S-64/Normal Procedures"

From
Jump to: navigation, search
(Start)
(Start)
Line 60: Line 60:
 
#Position lights as required
 
#Position lights as required
 
# #1 ENGINE START
 
# #1 ENGINE START
 
+
##Fireguard Posted
 
+
##N1 Lever to SHUTOFF
Fireguard Posted
+
##Press starter switch
N1 Lever to SHUTOFF
+
##Verify #1 ENG STARTER ON light illuminated
Press starter switch
+
##Verify Engine #1 N1 at least 20%.
Verify #1 ENG STARTER ON light illuminated
+
##WARNING – Do not turn IGN switches ON if N1 is below 20%. A fire or engine explosion may result. #1 ##IGN switch ON
Verify Engine #1 N1 at least 20%.
+
##Advance N1 lever to GRD IDLE
WARNING – Do not turn IGN switches ON if N1 is below 20%. A fire or engine explosion may result. #1 IGN switch ON
+
##Check ENG #1 gauges in green and #1 ENG STARTER light OUT.
Advance N1 lever to GRD IDLE
+
#ROTOR ENGAGEMENT
Check ENG #1 gauges in green and #1 ENG STARTER light OUT.
+
##Outside area clear
ROTOR ENGAGEMENT
+
##ROTOR BRAKE switch to OFF.
Outside area clear
+
##Verify ROTOR BRAKE ON and ROTOR BRAKE PRESS caution lights OUT.
ROTOR BRAKE switch to OFF.
+
##Advance ENG #1 N1 levers to FULL OPEN
Verify ROTOR BRAKE ON and ROTOR BRAKE PRESS caution lights OUT.
+
##Verify FIRST STAGE SERVRO pressure advance to GREEN ARC and 1ST STAGE SERVO caution light OUT
Advance ENG #1 N1 levers to FULL OPEN
+
##Verify transmission pressure and temperature indications in GREEN ARC.
Verify FIRST STAGE SERVRO pressure advance to GREEN ARC and 1ST STAGE SERVO caution light OUT
+
##Verify #1 ENGINE RPM and ROTOR RPM in GREEN ARC.
Verify transmission pressure and temperature indications in GREEN ARC.
+
# #2 ENGINE START
Verify #1 ENGINE RPM and ROTOR RPM in GREEN ARC.
+
##Fireguard Posted
#2 ENGINE START
+
##N1 Lever to SHUTOFF
Fireguard Posted
+
##Press starter switch
N1 Lever to SHUTOFF
+
##Verify #2 ENG STARTER ON light illuminated
Press starter switch
+
##Verify Engine #2 N1 at least 20%.
Verify #2 ENG STARTER ON light illuminated
+
##WARNING – Do not turn IGN switches ON if N1 is below 20%. A fire or engine explosion may result.
Verify Engine #2 N1 at least 20%.
+
## #2 IGN switch ON
WARNING – Do not turn IGN switches ON if N1 is below 20%. A fire or engine explosion may result.
+
##Advance N1 lever to GRD IDLE
#2 IGN switch ON
+
##Check ENG #2 gauges in green and #2 ENG STARTER light OUT.
Advance N1 lever to GRD IDLE
+
##Advance N1 lever to FULL OPEN
Check ENG #2 gauges in green and #2 ENG STARTER light OUT.
+
##Check 2ND STAGE SERVO light OUT
Advance N1 lever to FULL OPEN
+
##Verify #2 ENGINE RPM in GREEN ARC
Check 2ND STAGE SERVO light OUT
+
#After Engine Start
Verify #2 ENGINE RPM in GREEN ARC
+
##IGN switches OFF
After Engine Start
+
##APP STOP
IGN switches OFF
+
##APP MASTER switch OFF
APP STOP
+
##ANTI-ICE switches as required
APP MASTER switch OFF
 
ANTI-ICE switches as required
 
  
 
===Takeoff and Climb===
 
===Takeoff and Climb===
 
===Pre-Landing===
 
===Pre-Landing===
 
===Shutdown===
 
===Shutdown===

Revision as of 03:02, 4 August 2021

SECTION 4. NORMAL PROCEDURES

1 Start

  1. PARKING BRAKE and NOSEWHEEL LOCK set.
  2. MASTER SWITCH panel switches as follows
    1. EXT POWER as required, ON for GPU start
    2. INV, IGN, GEN, RECT, POD PWR, ANTI-ICE switches OFF
    3. LDG GEAR in JACK position
    4. TAIL SKID as required
  3. BATT switch ON – check for illumination of caution lights.
  4. GPU connect as required
  5. FUEL switches
    1. FWD and AFT tank switches OFF
    2. AUX pump switches OFF
  6. FUEL SHUTOFF levers OFF
  7. N1 levers to SHUT OFF
  8. Overhead panel switches set as follows:
    1. Light switches as required
    2. APP MASTER switch OFF
  9. Check all circuit breakers IN
  10. Check advisory panel lights. The following lights should be on: #1 GENERATOR, #2 GENERATOR, #1 RECTIFIER, #2 RECTIFIER, #1 FUEL PRESS, #2 FUEL PRESS, 1ST STAGE SERVO, AFCS SERVO PRESS, 2ND STAGE SERVO, CO-PILOT PITOT HEAT, HOIST OIL PRESS, PILOT PITOT HEAT, ROTOR BRAKE PRESS, 1ST STAGE TAIL ROTOR SERVO, PARKING BRAKE ON
  11. Caution panel TEST switch to TEST. Verify all caution lights ON.
  12. Caution panel TEST switch to NORMAL.
  13. Fireguard Posted
  14. APP Clear
  15. APP Start
    1. MASTER switch ON
    2. Check LOW PRESS light ON
    3. APP Start, press and hold until APP N1 at 40%.
  16. GEN and RECT switches ON.
  17. Check GENERATOR and RECTIFIER caution lights out.
  18. Check transmission, utility hydraulic and hoist hydraulic pressure normal.
  19. INV switch ON
  20. Generators & Inverter Check
    1. #1 GEN switch OFF
    2. Check #1 GEN caution light ON, #1 and #2 RECT lights OFF.
    3. #2 GEN switch OFF
    4. Check #2 GEN light ON, #1 and #2 RECT light OFF.
    5. INV switch OFF
    6. Check #1 and #2 RECT lights ON
    7. #1 GEN, #2 GEN and INV switches ON
    8. Check GEN and RECT lights OFF
  21. GPU disconnect. EXT PWR switch OFF.
  22. PITOT HEAT switch ON. Check caution lights OUT.
  23. ROTOR BRAKE switch OFF, check caution light OUT.
  24. ROTOR BRAKE switch ON.
  25. FUEL SYSTEM
    1. #1 ENG FUEL PUMP switches ON
    2. Check ENG #1 pump lights OUT, #1 and #2 FUEL PRESS lights remain ON.
    3. Open #1 fuel valve. #1 FUEL PRESS light OUT.
    4. X-FEED switch ON. #2 FUEL PRESS remains ON.
    5. Open #2 fuel valve. #2 FUEL PRESS light OUT.
    6. X-FEED switch to CLOSE. #2 FUEL PRESS light ON.
    7. #2 ENG FUEL PUMP switches ON. #2 FUEL PRESS light OUT.
    8. AUX FUEL PUMP switches OFF
    9. FUEL TEST IND switch to IND. Verify fuel gauges read zero.
    10. FUEL TEST IND switch to CONT. Verify sufficient fuel levels.
  26. Tail skid DOWN
  27. Anti-collision lights ON
  28. Position lights as required
  29. #1 ENGINE START
    1. Fireguard Posted
    2. N1 Lever to SHUTOFF
    3. Press starter switch
    4. Verify #1 ENG STARTER ON light illuminated
    5. Verify Engine #1 N1 at least 20%.
    6. WARNING – Do not turn IGN switches ON if N1 is below 20%. A fire or engine explosion may result. #1 ##IGN switch ON
    7. Advance N1 lever to GRD IDLE
    8. Check ENG #1 gauges in green and #1 ENG STARTER light OUT.
  30. ROTOR ENGAGEMENT
    1. Outside area clear
    2. ROTOR BRAKE switch to OFF.
    3. Verify ROTOR BRAKE ON and ROTOR BRAKE PRESS caution lights OUT.
    4. Advance ENG #1 N1 levers to FULL OPEN
    5. Verify FIRST STAGE SERVRO pressure advance to GREEN ARC and 1ST STAGE SERVO caution light OUT
    6. Verify transmission pressure and temperature indications in GREEN ARC.
    7. Verify #1 ENGINE RPM and ROTOR RPM in GREEN ARC.
  31. #2 ENGINE START
    1. Fireguard Posted
    2. N1 Lever to SHUTOFF
    3. Press starter switch
    4. Verify #2 ENG STARTER ON light illuminated
    5. Verify Engine #2 N1 at least 20%.
    6. WARNING – Do not turn IGN switches ON if N1 is below 20%. A fire or engine explosion may result.
    7. #2 IGN switch ON
    8. Advance N1 lever to GRD IDLE
    9. Check ENG #2 gauges in green and #2 ENG STARTER light OUT.
    10. Advance N1 lever to FULL OPEN
    11. Check 2ND STAGE SERVO light OUT
    12. Verify #2 ENGINE RPM in GREEN ARC
  32. After Engine Start
    1. IGN switches OFF
    2. APP STOP
    3. APP MASTER switch OFF
    4. ANTI-ICE switches as required

2 Takeoff and Climb

3 Pre-Landing

4 Shutdown