Difference between revisions of "H-34 Choctaw/Mission Equipment"

From
Jump to: navigation, search
(Hoist Operation)
(Attaching Loads to the Hook)
 
(22 intermediate revisions by 2 users not shown)
Line 40: Line 40:
 
[[File:S58-cyclic.png|thumb|right|150px|
 
[[File:S58-cyclic.png|thumb|right|150px|
 
<figure id='fig:pilot-winch'><caption>Pilot Winch Controls</caption></figure>]]
 
<figure id='fig:pilot-winch'><caption>Pilot Winch Controls</caption></figure>]]
[[File:s61-crew-winch-control.png|thumb|right|150px|
+
[[File:s58-crew-winch-control.png|thumb|right|150px|
 
<figure id='fig:crew-winch'><caption>Crew Winch Controls</caption></figure>]]
 
<figure id='fig:crew-winch'><caption>Crew Winch Controls</caption></figure>]]
  
 
===== Pilot Control =====
 
===== Pilot Control =====
  
To use the pilot winch controls (see <xr id='fig:pilot-winch'/>), the HOIST MASTER switch on the upper panel must be set to PILOT.  The hoist control panel, located on the lower consoled, consists of a single three-position rocker switch with UP, DOWN and a center HOLD positionThe switch is spring loaded to the HOLD position.
+
To use the pilot winch controls (see <xr id='fig:pilot-winch'/>), the HOIST switch on the upper panel must be set to PILOT.  The hoist controls are located on the cyclic on a rocker switch labeled HOISTPress the top part of the switch to move the hoist up, and the bottom part to move it down.
  
A pilot hoist shear switch is located on the upper console.  This switch can be used in the event the cable becomes entangled and must be cut free to ensure the safety of the helicopter.  The switch has a guard which must be opened before activating the switch.  The shear switch is active regardless of the position of the HOIST MASTER.
+
A pilot hoist shear switch is located on the upper console.  This switch can be used in the event the cable becomes entangled and must be cut free to ensure the safety of the helicopter.  The switch has a guard which must be opened before activating the switch.  The shear switch is active regardless of the position of the HOIST switch.
  
 
===== Crew Control =====
 
===== Crew Control =====
  
The crew winch controls (see <xr id='fig:crew-winch'/>) are located to the right of the main cabin door.  The HOIST MASTER switch on the upper panel must be set to CREW position to utilize them.  The main control is a lever that can be tilted to the left or right to lower or raise the winchThe amount by which the lever is tilted will affect the speed of the winch.
+
The crew winch controls (see <xr id='fig:crew-winch'/>) are located to the left of the main cabin door.  The HOIST switch on the upper panel must be set to CREW position to utilize them.  The controls consist of a press-and-hold rocker switch with UP, OFF, and DN positionsPress and hold the switch in the UP or DN position to move the hoist up or down, respectively.
  
 
The crew member occupying the hoist operator seat (kneeling by the  main door), can also use key controls to control the winch.  Use PgDown to lower the winch, and PgUp to raise it.  These controls are only active when the hoist is in crew mode.
 
The crew member occupying the hoist operator seat (kneeling by the  main door), can also use key controls to control the winch.  Use PgDown to lower the winch, and PgUp to raise it.  These controls are only active when the hoist is in crew mode.
  
A crew hoist shear switch is located above and to the right of the hoist control.  It is covered by a switch guard which must be opened to activate the shear.  The shear panel also includes a shear test switch.  To test the shear switch, first set the shear test switch to TEST.  Then open and activate the shear switch.  If the green test light comes on, then the shear circuitry is operating correctly.  Be sure to turn off the shear switch and close the guard before turning off the test switch.
+
A crew hoist shear switch is located next to the hoist control.  It is covered by a switch guard which must be opened to activate the shear.
  
 
===== HUD Control =====
 
===== HUD Control =====
Line 96: Line 96:
 
|w r|| Deploy the rope
 
|w r|| Deploy the rope
 
|}
 
|}
 +
 +
==== Rappelling Rope ====
 +
 +
Unlike the baskets and harness, the rope attaches to a ring on the bottom of the winch. The rope can be used to quickly egress from the helicopter in a high hover to the surface. Click on the orange rope bag to deploy the rope.
 +
 +
Any passenger in the main cabin may use the rope by clicking on the rope or the winch body. This will position the user at the top of the rope in a rappelling pose. Use the down arrow to control descent. Once at the bottom, the user will automatically unsit from the rope and aircraft.
 +
==== Hoist Limits ====
 +
Operating Limits
 +
*Duty Cycle: Continuous
 +
*Maximum load: 300 pounds lowering, 600 pounds raising
 +
*Maximum Airspeed with Hoist Cable Extended: 50 kias
 +
 +
=== Cargo Hook ===
 +
 +
[[File:S58-hook-tie.jpg|thumb|right|
 +
<figure id='fig:hook-tie'><caption>Cargo Hook Tiedown</caption></figure>]]
 +
[[File:S58-clutch-hook.png|thumb|right|100px|
 +
<figure id='fig:hook-controls'><caption>Cargo Hook Controls</caption></figure>]]
 +
 +
A cargo hook on the underside of the aircraft can be used to carry sling loads.  Cargo loads are attached by crew members outside the aircraft while the aircraft is in a low hover.
 +
 +
==== Raising/Lowering the Cargo Hook ====
 +
 +
The cargo hook is raised and lowered through a tiedown cleat in the main cabin (see <xr id="fig:hook-tie"/>).  Clicking the cleat will toggle the position of the cargo hook.  The cargo hook must be lowered in order to attach a load, and the hook cannot be raised if there is a load on it.
 +
 +
==== Cargo Hook Controls ====
 +
 +
The Cargo Hook system is controlled and monitored the cargo control panel(see <xr id="fig:hook-controls"/>) and a release switch on the cyclic.  Each of the elements has the following function:
 +
* CARGO SLING MASTER switch - Has positions ON, SAFE and AUTO.  In the ON and AUTO positions, the CARGO (hook release) button the cyclic is active, and pressing that button will release any sling load.  In the AUTO position, the hook will also auto release when a load is set on the ground after being picked up.  In the SAFE positions, the CARGO button is disabled to prevent accidental release.
 +
* CARGO button - Releases the hook and any sling load on it. This switch is disabled when the CARGO HOOK switch is in the SAFE position.
 +
* REL light - Illuminates when the load is released.
 +
* LOCK OFF light - Illuminates when the CARGO SLING MASTER switch is not in the SAFE position.
 +
 +
==== Attaching Loads to the Hook ====
 +
The CARGO SLING MASTER switch should be set to ON during load attachment and pickup to allow to the load to be released in the event problems occur.
 +
 +
Loads are normally attached by ground personnel while the pilot maneuvers the helicopter over the load. Use the following procedure to attach the load.
 +
#Rez the load right-side up on the ground.
 +
#Have pilot fly into position over the load.
 +
#Deploy the Cargo hook. (See section 2.1)
 +
#Ground personnel clicks on one of the loops to "hold" it. The loop will maintain the distance from the avi at the time it was clicked. Use mouselook to move the loop and maneuver it onto a hook.
 +
#Once the look is attached to the hook, signal the pilot to pick up the load.
 +
 +
==== Flying with a Hook Load ====
 +
 +
Once a load is attached, the load will drag on the ground in non-physical mode until cables have stretched to their hang distance. When picking up a load it is important to pick straight up until the load breaks contact with the ground and is hanging freely.
 +
While flying with a load, the maximum allowed airspeed is 120 knots. It is also recommended to make sim crossings away from corners and as near to a right angle as possible. The CARGO HOOK switch should be set to SAFE once the load is airborne, until such time as the load is ready to be released.
 +
 +
==== Building Loads ====
 +
 +
The S-58 is packaged with a hook kit allowing you to build and share your own loads for the cargo hook system. The system is compatible with the Chinook hook load system, but since the S-58 only has a single hook, only load with a single loop can be used.
 +
 +
The system is designed to offer a great deal of flexibility in how you configure your loads. The prim components of the system are full perm, while the script is copy/transfer allowing you to share any loads you create. The primary prim components of a load are:
 +
* sa-hookLoop - This is the actual loop that is attached to the hook on the helicopter.
 +
* sa-anchor - Anchor point on the load.
 +
* sa-cable - Cable connecting the loop and the load.
 +
 +
You can detach these from the built-in loads to create your own loads.
 +
 +
For each hook loop, you can include one to four cables and anchors. Edit the anchor to its desired position on the load, and the hook loop to its "resting" position to were it will be returned when the loop is not attached to a hook, and not held by an avatar. The cables may be placed anywhere and will be automatically adjusted when the script is dropped onto the load or reset. Note that the root prim should be positioned so that is is "right side up" (i.e., rotation other than z-rotation is 0).
 +
 +
Once you have edited the anchors and loops where you want them, drop in the script, or reset the script if it is already installed (simply pull the script from one of the included loads). The cables will arrange themselves to attach between a loop and one or two anchors. The closest two anchors to each loop will be used.
 +
 +
Several menu options are available for loads. The load menu can only be accessed by the owner and is brought up by clicking on an anchor. Available options are:
 +
 +
* Link Msg - This is an option than can be turned on/off. When the option is on, a link message with a integer value of -749203379 will be sent when the load changes states (e.g., suspended or not suspended). This message can be intercepted by other scripts to perform other customized actions.
 +
* Hang Height - Sets the height below the helicopter at which the load will hang.
 +
* Access - Sets who can manipulate the hook loops. Default is anyone.
 +
* Stat Drp - Enables/disabled static drop mode. When static drop is enabled, the cargo load will turn static when dropped rather than staying physical. This can be useful for dropping boats on the water surface.

Latest revision as of 19:24, 6 March 2022

SECTION 9. MISSION EQUIPMENT

Figure 1: S-58 Hoist System

1 Rescue Hoist

1.1 Overview

The S-58 is equipped with a rescue hoist mounted above the main cabin door. The hoist is powered by the utility hydraulic system with control circuits powered by the DC bus. A switch on the overhead panel labeled HOIST has positions CREW, OFF and PILOT to disabled the system, or give control the either the pilot or the crew. When the winch is not in use, it is recommended that it be kept in the fully retracted position with no load and the HOIST switch in the OFF position. This will disable the timer loop in the hoist script and reduce script lag.

1.2 Hoist Loads

1.2.1 Load Types

The hoist is capable of being used with the following loads:

Device Use
Harness Used for deployment and retrieval of rescuers only. Never to be used for patients
Rescue Basket Used for the rescue of uninjured or lightly injured patients. May also be used for the deployment and retrieval of divers or rescuers not trained in hoist operations. Do not use for patients with suspected back injuries or broken bones.
Stokes Basket Used for the rescue of injured patients, may be used in conjunction with the harness to allow a rescuer to attend to the patient during the hoisting process
Rope Used for the deployment of rescuers by rappelling. This is the preferred method of deployment on land or onto objects such as boats as the rescuer can control their own descent, which increases safety. It is also faster than lowering by hoist.
1.2.2 Deploying

A load is generally deployed by clicking on it. For the rope and the harness, you can click on one of the bags in the storage area near the cabin door. The smaller yellow bag contains the harness, while the larger orange bag contains the rope. The rescue basket, stokes basket and forest penetrator are configured as a sit target as its default touch action, so a simple left click will result in sitting on that piece of equipment. If it is necessary to deploy rescue equipment while not sitting in the helicopter you can right click on it and select "Touch". If other rescue equipment is already deployed, the selected equipment will be swapped into the helicopter before the new equipment is swapped out. Clicking on the hook, will swap in all equipment. No more than 1m of cable should be deployed when swapping loads/out.

Except for the stokes basket, it is necessary to move into the helicopter before moving any rescue equipment back into the helicopter. This can be done by clicking on an empty seat in the helicopter to move into it. The stokes basket can be moved into the helicopter with a patient using it as long as the seats on the right side of the helicopter are in the up position. If a patient subsequently moves out of the stokes basket while the helicopter is in the aircraft, the stokes basket will be moved to the stowed position.

1.3 Hoist Operation

Warning: Due to SL physics limitations, the hoist loads must be kept at least 1 meter from any solid object or surface, failure to do so will endanger the aircraft

Figure 2: Pilot Winch Controls
Figure 3: Crew Winch Controls
1.3.1 Pilot Control

To use the pilot winch controls (see Figure 2), the HOIST switch on the upper panel must be set to PILOT. The hoist controls are located on the cyclic on a rocker switch labeled HOIST. Press the top part of the switch to move the hoist up, and the bottom part to move it down.

A pilot hoist shear switch is located on the upper console. This switch can be used in the event the cable becomes entangled and must be cut free to ensure the safety of the helicopter. The switch has a guard which must be opened before activating the switch. The shear switch is active regardless of the position of the HOIST switch.

1.3.2 Crew Control

The crew winch controls (see Figure 3) are located to the left of the main cabin door. The HOIST switch on the upper panel must be set to CREW position to utilize them. The controls consist of a press-and-hold rocker switch with UP, OFF, and DN positions. Press and hold the switch in the UP or DN position to move the hoist up or down, respectively.

The crew member occupying the hoist operator seat (kneeling by the main door), can also use key controls to control the winch. Use PgDown to lower the winch, and PgUp to raise it. These controls are only active when the hoist is in crew mode.

A crew hoist shear switch is located next to the hoist control. It is covered by a switch guard which must be opened to activate the shear.

1.3.3 HUD Control
Figure 4: S61 Winch HUD

The winch HUD (see Figure 4) can be used to control the winch by any crew member in the the helicopter. In order for the HUD to be active, the helicopter must have hydraulic and electrical power, and the HOIST switch must be in the CREW position. The winch HUD has two buttons on the left side to raise and lower the winch. A digital display shows the current cable length and the current height above the ground. A dial on the right-hand side sets the winch speed. Finally an emergency cable cut button with a guard is located on the top portion of the HUD.

1.3.4 Winch Chat Commands

The winch can also be controlled through the chat commands. The HOIST switch must be set to CREW in order to use the chat commands. The available commands are:

Command Description
w n Move which so that n meters of cable are deployed.
w u n Move which up by n meters.
w d n Move which down by n meters.
w cut Cut the cable.
w + Increase winch speed (by chat)
w - Decrease winch speed (by chat)
w x Stow all hook loads
w b Deploy the rescue basket
w s Deploy the stokes basket
w h Deploy the harness
w sh Deploy the harness and stokes basket together
w r Deploy the rope

1.4 Rappelling Rope

Unlike the baskets and harness, the rope attaches to a ring on the bottom of the winch. The rope can be used to quickly egress from the helicopter in a high hover to the surface. Click on the orange rope bag to deploy the rope.

Any passenger in the main cabin may use the rope by clicking on the rope or the winch body. This will position the user at the top of the rope in a rappelling pose. Use the down arrow to control descent. Once at the bottom, the user will automatically unsit from the rope and aircraft.

1.5 Hoist Limits

Operating Limits

  • Duty Cycle: Continuous
  • Maximum load: 300 pounds lowering, 600 pounds raising
  • Maximum Airspeed with Hoist Cable Extended: 50 kias

2 Cargo Hook

Figure 5: Cargo Hook Tiedown
Figure 6: Cargo Hook Controls

A cargo hook on the underside of the aircraft can be used to carry sling loads. Cargo loads are attached by crew members outside the aircraft while the aircraft is in a low hover.

2.1 Raising/Lowering the Cargo Hook

The cargo hook is raised and lowered through a tiedown cleat in the main cabin (see Figure 5). Clicking the cleat will toggle the position of the cargo hook. The cargo hook must be lowered in order to attach a load, and the hook cannot be raised if there is a load on it.

2.2 Cargo Hook Controls

The Cargo Hook system is controlled and monitored the cargo control panel(see Figure 6) and a release switch on the cyclic. Each of the elements has the following function:

  • CARGO SLING MASTER switch - Has positions ON, SAFE and AUTO. In the ON and AUTO positions, the CARGO (hook release) button the cyclic is active, and pressing that button will release any sling load. In the AUTO position, the hook will also auto release when a load is set on the ground after being picked up. In the SAFE positions, the CARGO button is disabled to prevent accidental release.
  • CARGO button - Releases the hook and any sling load on it. This switch is disabled when the CARGO HOOK switch is in the SAFE position.
  • REL light - Illuminates when the load is released.
  • LOCK OFF light - Illuminates when the CARGO SLING MASTER switch is not in the SAFE position.

2.3 Attaching Loads to the Hook

The CARGO SLING MASTER switch should be set to ON during load attachment and pickup to allow to the load to be released in the event problems occur.

Loads are normally attached by ground personnel while the pilot maneuvers the helicopter over the load. Use the following procedure to attach the load.

  1. Rez the load right-side up on the ground.
  2. Have pilot fly into position over the load.
  3. Deploy the Cargo hook. (See section 2.1)
  4. Ground personnel clicks on one of the loops to "hold" it. The loop will maintain the distance from the avi at the time it was clicked. Use mouselook to move the loop and maneuver it onto a hook.
  5. Once the look is attached to the hook, signal the pilot to pick up the load.

2.4 Flying with a Hook Load

Once a load is attached, the load will drag on the ground in non-physical mode until cables have stretched to their hang distance. When picking up a load it is important to pick straight up until the load breaks contact with the ground and is hanging freely. While flying with a load, the maximum allowed airspeed is 120 knots. It is also recommended to make sim crossings away from corners and as near to a right angle as possible. The CARGO HOOK switch should be set to SAFE once the load is airborne, until such time as the load is ready to be released.

2.5 Building Loads

The S-58 is packaged with a hook kit allowing you to build and share your own loads for the cargo hook system. The system is compatible with the Chinook hook load system, but since the S-58 only has a single hook, only load with a single loop can be used.

The system is designed to offer a great deal of flexibility in how you configure your loads. The prim components of the system are full perm, while the script is copy/transfer allowing you to share any loads you create. The primary prim components of a load are:

  • sa-hookLoop - This is the actual loop that is attached to the hook on the helicopter.
  • sa-anchor - Anchor point on the load.
  • sa-cable - Cable connecting the loop and the load.

You can detach these from the built-in loads to create your own loads.

For each hook loop, you can include one to four cables and anchors. Edit the anchor to its desired position on the load, and the hook loop to its "resting" position to were it will be returned when the loop is not attached to a hook, and not held by an avatar. The cables may be placed anywhere and will be automatically adjusted when the script is dropped onto the load or reset. Note that the root prim should be positioned so that is is "right side up" (i.e., rotation other than z-rotation is 0).

Once you have edited the anchors and loops where you want them, drop in the script, or reset the script if it is already installed (simply pull the script from one of the included loads). The cables will arrange themselves to attach between a loop and one or two anchors. The closest two anchors to each loop will be used.

Several menu options are available for loads. The load menu can only be accessed by the owner and is brought up by clicking on an anchor. Available options are:

  • Link Msg - This is an option than can be turned on/off. When the option is on, a link message with a integer value of -749203379 will be sent when the load changes states (e.g., suspended or not suspended). This message can be intercepted by other scripts to perform other customized actions.
  • Hang Height - Sets the height below the helicopter at which the load will hang.
  • Access - Sets who can manipulate the hook loops. Default is anyone.
  • Stat Drp - Enables/disabled static drop mode. When static drop is enabled, the cargo load will turn static when dropped rather than staying physical. This can be useful for dropping boats on the water surface.