Difference between revisions of "S-61R Pelican/Water Operations"

From
Jump to: navigation, search
(Water Taxi)
(Bilge Pump)
 
(11 intermediate revisions by the same user not shown)
Line 8: Line 8:
 
!Description
 
!Description
 
|-
 
|-
|wind ''dir' [''speed'']||Set wind to the compass direction ''dir''.  An optional speed parameter ''speed'' may be specified to set wind speed to between 0 and 3 m/s
+
|wind ''dir'' [''speed'']||Set wind to the compass direction ''dir''.  An optional speed parameter ''speed'' may be specified to set wind speed to between 0 and 3 m/s
 
|-
 
|-
 
|wind random||Set wind direction to random.
 
|wind random||Set wind direction to random.
Line 14: Line 14:
  
 
=== Anchor ===
 
=== Anchor ===
 +
 +
[[File:S61-anchor-lights.png|thumb|right|
 +
<figure id="fig:anchor-lights"><caption>Anchor Lights</caption></figure>
 +
]]
 +
 +
An anchor can be deployed to prevent the aircraft from drifting while on water.  The anchor is located in a storage area next to the main cabin door.  Click on the anchor (or anchor storage area) to deploy or stow the anchor.  The main door must be open, and the aircraft must be on water to deploy the anchor.  You can also use the chat commands "anchor" and "unanchor" to deploy or stow the anchor.
 +
 +
When the aircraft is anchored and remains physical, the aircraft will react to the current wind.  Typically this will cause the aircraft to slowly align into the wind in the direction of the anchor.
 +
 +
==== Anchor Lights ====
 +
 +
While anchored, it is recommended that the anchor lights (see <xr id='fig:anchor-lights'/>) be turned on.  The anchor light switch is located on the overhead panel.  The anchor light is powered by the hot battery bus and does not require the BATTERY switch to be ON.
  
 
=== Bilge Pump ===
 
=== Bilge Pump ===
 +
 +
<div style="clear: both" ></div>
 +
{| style="float: right"
 +
|
 +
[[File:S61-blige-box.png|thumb|left|200px|
 +
<figure id="fig:bilge-box><caption>Bilge Pump Box</caption></figure>
 +
]]
 +
|
 +
[[File:S61-bilge-pump.png|thumb|right|
 +
<figure id="fig:bilge-pump><caption>Deployed Bilge Pump</caption></figure>
 +
]]
 +
|}
 +
 +
While on water, the flotation compartments will slowly fill with water.  If the compartments are not emptied, the weight of the water will cause serious performance issues during flight and on on-water operations.  A bilge pump is provided with the helicopter to expel any excess water that may have accumulated.  To deploy the bilge pump, click the box (<xr id='fig:bilge-box'/>) labeled "Bilge Pump" stored on the upper shelf in the storage area near the main cabin door.  The main cabin door must be open to deploy the bilge pump.  The bilge pump can be stowed by clicking on the box again.  It is recommended that the box be kept dry at all times.
 +
 +
The bilge pump will deploy on the floor on the right side of the aircraft near the main cabin door (see <xr id='fig:bilge-pump'/>).  The pump intake connects to a port leading into the bilge, while the pump outtake leads overboard off the side of the aircraft.  Click on the pump repeatedly to raise and lower the pump handle.  Continue pumping until no additional water is flushed out the hose.

Latest revision as of 18:10, 21 June 2020

SECTION 10. WATER OPERATIONS

1 Water Taxi

The S-61R is constructed with a water-tight hull with 4 flotation compartments to allow it to land and operate on water. Water taxi is performed similarly to ground taxi: apply a small amount of collective to produce thrust, then apply forward cyclic to move forward. Use the anti-torque pedals to steer on water. The S-61R includes an internal wind system that affects its movement on water. By default the wind direction is random and changes direction on average about every 10 min (with some variation). Use the following commands to control the wind model:

Command Description
wind dir [speed] Set wind to the compass direction dir. An optional speed parameter speed may be specified to set wind speed to between 0 and 3 m/s
wind random Set wind direction to random.

2 Anchor

Figure 1: Anchor Lights

An anchor can be deployed to prevent the aircraft from drifting while on water. The anchor is located in a storage area next to the main cabin door. Click on the anchor (or anchor storage area) to deploy or stow the anchor. The main door must be open, and the aircraft must be on water to deploy the anchor. You can also use the chat commands "anchor" and "unanchor" to deploy or stow the anchor.

When the aircraft is anchored and remains physical, the aircraft will react to the current wind. Typically this will cause the aircraft to slowly align into the wind in the direction of the anchor.

2.1 Anchor Lights

While anchored, it is recommended that the anchor lights (see Figure 1) be turned on. The anchor light switch is located on the overhead panel. The anchor light is powered by the hot battery bus and does not require the BATTERY switch to be ON.

3 Bilge Pump

Figure 2: Bilge Pump Box
Figure 3: Deployed Bilge Pump

While on water, the flotation compartments will slowly fill with water. If the compartments are not emptied, the weight of the water will cause serious performance issues during flight and on on-water operations. A bilge pump is provided with the helicopter to expel any excess water that may have accumulated. To deploy the bilge pump, click the box (Figure 2) labeled "Bilge Pump" stored on the upper shelf in the storage area near the main cabin door. The main cabin door must be open to deploy the bilge pump. The bilge pump can be stowed by clicking on the box again. It is recommended that the box be kept dry at all times.

The bilge pump will deploy on the floor on the right side of the aircraft near the main cabin door (see Figure 3). The pump intake connects to a port leading into the bilge, while the pump outtake leads overboard off the side of the aircraft. Click on the pump repeatedly to raise and lower the pump handle. Continue pumping until no additional water is flushed out the hose.