H-34 Choctaw/Appendices

From
< H-34 Choctaw
Revision as of 15:12, 10 September 2021 by Kelly (talk | contribs) (Weather Commands)
Jump to: navigation, search

SECTION 13. APPENDICES

1 COMMAND SUMMARY

Command Description
help Get link to aircraft documentation.
menu Post the main menu
cycen Center the cyclic
pedcen Center the pedals
cv/cv0/cv1/cv2/cv3 Change camera view: toggle/cockpit/behind/overhead/underside
fc/fc0/fc1/fc2 Fine control: toggle/off/fine/very-fine
dc Close all doors
rb/rb0/rb1 Toggle rotor brake/Rotor brake on/Rotor brake off
mlt Toggle "mouse look touch"
qstart Do a quick start (skip full start procedure)
qstop or stop Do a quick shutdown (skip full shutdown procedure)
hud Get copy of hud
winchhud/hoisthud Get copy of hoist hud
checklist Bring out or stow the checklist
s switch-name Toggle the switch named "switch-name"
s1 switch-name Turn on the switch named "switch-name"
s0 switch-name Turn off the switch named "switch-name"
sn switch-name Set rotary or three position switch to position n.
com1 freq Set the COM1 radio frequency to freq
com2 freq Set the COM2 radio frequency to freq
hf freq Set the HF radio frequency to freq
ap cmd Autopilot command
x cmd Transponder command
nav cmd Navigation/VOR command
w cmd Winch/Hoist command
wx cmd Weather command

1.1 Autopilot Commands

Regular ASE Commands:

Command Description
ap eng Hold the current airspeed and heading.
ap alt Hold the current altitude. The ENG channel must already be engaged for altitude hold to be engaged.
ap dis Disconnect the ASE.

Extended ASE Commands (must be enabled in @Realism menu):

Command Description
ap hdg n Turn to heading n.
ap r n Turn right by n degrees.
ap l n Turn left by n degrees.
ap u n Move up n feet.
ap d n Move down n feet.
ap hvr Enter autohover mode.
ap to Take off to a hover.
ap land Autoland the aircraft.

1.2 Transponder Commands

Command Description
x nnnn Set transponder code to nnnn

1.3 Navigation Commands

Command Description
nav nav1 freq Set NAV1 radio to freq
nav nav2 freq Set NAV2 radio to freq
nav obs1 hdg Set CD1 heading to hdg. Use "to" or "from" to set heading to/from station.
nav obs2 hdg Set CD2 heading to hdg. Use "to" or "from" to set heading to/from station.

1.4 Weather Commands

Command Description
wx auto Enabled basic weather model
wx disabled Disable all weather
wx temp n Set Temperature to n (Celsius)
wx vis n Set visibility to n miles (0 to 10)
wx precip n Set precipitation intensity to n (0 to 100)
wx ceil n Set ceiling (cloud bases) to n feet.
wx humidity n Set relative humidity to n percent (0 to 100)
wx wind dir speed Set wind to speed' knots (0-40) from direction dir (0-360)
wx vmc Set weather to VMC
wx imc Set weather to IMC

2 SWITCH SUMMARY

This section describes the various switches in the S-58 and their functions (used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches). Push buttons (marked with [b]), and rotary knobs (marked with [r]) are also shown here. Switches that are for RP purposes only and do not have an effect on the helicopter are marked [RP] in the description. For switches that have guards, the guard is addressed by appending a "-g" to the switch name (marked with [-g] after the name in the table below).

2.1 Switches

Name Description
inv Inverter Select
oildil Oil Dillution
bstpmp Boost Pump
clutch Clutch Engagement
fuelcutoff Fuel Cut-off
elt [ts] ELT
fan Cabin fan
pitot Pitot heat
read Passenger Reading Lights
posbrt Position light brightness
alarm[-g] Crew alarm
beacon Beacon
sticktrim Stick Trim
cablecut[-g] Hoist cable cut (cockpit)
radio Radio master
elecbarr Electric barrier door
brake Parking Brake
taillock Tailwheel Lock
floodlts [ts] Flood and hover lights
hoist [ts] Hoist Mode
heat [ts] Cabin Heat
posmode [ts] Position light mode
cabinlts [ts] Main cabin lights
dcpwr [ts] DC Power
ckptdome [ts] Cockpit dome light
hook [ts] Cargo hook mode
ldglts [ts] Landing Lights
servo [ts] Servo Mode
cabCableCut[-g] Hoist Cable Cut (cabin)
l-com1 COM1 listen
l-com2 COM2 listen
l-nav1 NAV1 listen
l-nav2 NAV2 listen
l-hf HF listen
l-uhf UHF listen

2.2 Knobs

Name Description Positions
emerlts Instrument Emergency Lights 0:off, 1-3:levels, 4:high
conalts Console A Panel Lights (copilot) 0:off, 1-3:levels, 4:high
nonfltlts Non-Flight Instrument Lights 0:off, 1-3:levels, 4:high
fltlts Flight Instrument Lights (pilot) 0:off, 1-3:levels, 4:high
mags Magnetos/Ignition 0:OFF, 1:L, 2:R, 4:BOTH
fuelsel Fuel Indicator Select 0:TOT, 1:FWD, 2:CTR, 3:AFT
xpdr Transponder Mode 0:off, 1:sby: 2:on, 3:alt, 4:tst
cgtrim CG Trim 0:F3, 1:F2, 2:F1, 3:CTR, 4:A1, 5:A2, 6:A3
yawtrim Yaw Trim 0:L4, 1:L3, 2:L2, 3:L1, 4:CTR, 5:R1, 6:R2, 7:R3, 8:R4
txsel Transmit Select 0:COM1, 1:COM2, 2:HF, 3:UHF
wipers Windshield Wipers 0:Park, 1:Off, 2:Fast, 3:Med, 4:Slow