MD-500D/Servicing

From
< MD-500D
Revision as of 03:54, 21 November 2026 by Kelly (talk | contribs) (Created page with " <span class=sa-section>SECTION 8. SERVICING</span> === General === This section describes the servicing and maintenance requirements for the MD-500D helicopter, including s...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

SECTION 8. SERVICING

1 General

This section describes the servicing and maintenance requirements for the MD-500D helicopter, including scheduled component replacement, maintenance inspections, and refueling.

The MD-500D incorporates a component maintenance tracking system which records operating time, installation dates, and component condition. Components must be serviced or replaced at the prescribed intervals to maintain aircraft airworthiness.

2 Maintenance Workbench

The MD-500D maintenance workbench provides facilities for inspection, servicing, and replacement of aircraft components.

The workbench contains the equipment and tools required for maintenance, including replacement components, a maintenance computer, and an aircraft maintenance logbook.

2.1 Component Inspection

The maintenance computer provides a record of the installed components and their current service condition.

For each component, the following information is recorded:

  • ID - Unique identifier assigned to the component.
  • Component - Name of the installed component.
  • Service Time - Prescribed service interval in operating hours.
  • Install Date - Date and time at which the component was installed.
  • Install HOBBS - Aircraft Hobbs meter reading at installation.
  • Remaining Time - Operating hours remaining before scheduled replacement.
  • Wear - Accumulated component wear or degradation.

The remaining service time is calculated from the component's installation Hobbs reading and the current aircraft Hobbs reading.

Component wear is tracked separately from service time. A component may require replacement due to excessive wear even when its scheduled service interval has not expired.

2.2 Component Replacement

Components requiring replacement shall be identified using the maintenance computer.

Replacement components must be of the correct type and properly installed before returning the aircraft to service.

Following replacement, the maintenance record shall be updated to reflect the new installation date, installation Hobbs reading, and component condition.

2.3 Maintenance Records

The aircraft maintenance logbook provides a record of component servicing and replacement.

Maintenance records should include the component serviced, the date of maintenance, aircraft operating hours, and any discrepancies noted during inspection.

3 Component Service Intervals

The following table identifies the components subject to scheduled replacement and their prescribed service intervals.

ID Component Service Interval
0 Engine Core 100 hours
1 Main Rotor 200 hours
2 Tail Rotor 200 hours
3 Main Rotor Transmission 150 hours
4 Tail Rotor Transmission 150 hours
5 Generator/Starter 20 hours
6 Fuel Filter 20 hours
7 Fuel Pump 30 hours
8 Starter Pump 50 hours
9 Wiring Harness 400 hours
10 Battery 50 hours
11 Floats 50 hours
12 Fuel Controller 25 hours
13 Engine Air Particle Separator (EAPS) 100 hours

Service intervals are measured in aircraft operating hours as recorded by the Hobbs meter.

Components that exhibit excessive wear, damage, or malfunction shall be replaced regardless of remaining service time.

4 Powerplant Servicing

4.1 Engine Core

The engine core is subject to a scheduled service interval of 100 operating hours.

Engine condition should be evaluated through inspection of engine performance, temperature, and operating characteristics.

Excessive engine wear may result in reduced available power, increased turbine outlet temperature, or other abnormal operating conditions.

4.2 Generator/Starter

The combined generator/starter is subject to a scheduled service interval of 20 operating hours.

The unit provides electrical power for engine starting and operates as a generator following engine start.

4.3 Fuel System Components

The following fuel system components require periodic replacement:

  • Fuel Filter - 20 hours.
  • Fuel Pump - 30 hours.
  • Starter Pump - 50 hours.
  • Fuel Controller - 25 hours.

Fuel system components shall be inspected for proper operation and replaced when service limits are reached.

4.4 Engine Air Particle Separator

The engine air particle separator (EAPS) is subject to a scheduled service interval of 100 operating hours.

The EAPS reduces the ingestion of airborne contaminants into the engine. The system shall be inspected for damage and excessive wear.

5 Rotor and Transmission Servicing

5.1 Main Rotor

The main rotor assembly is subject to a scheduled service interval of 200 operating hours.

The rotor assembly shall be inspected for damage, excessive wear, and other conditions affecting safe operation.

5.2 Tail Rotor

The tail rotor assembly is subject to a scheduled service interval of 200 operating hours.

The tail rotor shall be inspected for blade damage, excessive wear, and proper mechanical condition.

5.3 Main Rotor Transmission

The main rotor transmission is subject to a scheduled service interval of 150 operating hours.

The transmission transfers engine power to the main rotor and tail rotor drive system.

5.4 Tail Rotor Transmission

The tail rotor transmission is subject to a scheduled service interval of 150 operating hours.

The transmission shall be inspected for excessive wear and indications of mechanical deterioration.

6 Electrical System Servicing

6.1 Battery

The battery is subject to a scheduled service interval of 50 operating hours.

Battery condition shall be evaluated during servicing. A battery exhibiting excessive wear or failure to maintain adequate charge shall be replaced.

6.2 Wiring Harness

The aircraft wiring harness is subject to a scheduled service interval of 400 operating hours.

The wiring harness distributes electrical power and control signals throughout the aircraft.

Excessive wear or damage to the wiring harness may result in electrical system malfunctions.

7 Emergency Flotation Equipment

The emergency flotation equipment is subject to a scheduled service interval of 50 operating hours.

The flotation system shall be inspected for damage, deterioration, and proper installation.

Components that have been damaged or otherwise rendered unserviceable shall be replaced before further operation requiring emergency flotation capability.

8 Fuel

8.1 Fuel Types

The MD-500D is equipped with an Allison 250-C20B turboshaft engine.

Approved fuels include:

Usage Fuel Type Restrictions
Normal Jet A / Jet A-1 Unlimited use
Normal JP-4 / JP-5 / JP-8 Unlimited use
Emergency Approved aviation gasoline Subject to engine operating restrictions

Use of emergency aviation gasoline is limited to six hours per engine overhaul period.

When operating on alternate or emergency fuel, the start pump must remain on until engine shutdown.

8.2 Refueling

Before refueling, the aircraft shall be parked with the engine shut down and electrical equipment secured.

  1. Park helicopter in a suitable refueling area.
  2. Engine - OFF.
  3. Battery switch - OFF.
  4. Ground aircraft - CONNECT.
  5. Fuel filler cap - REMOVE.
  6. Verify correct fuel type.
  7. Refuel aircraft to desired quantity.
  8. Fuel filler cap - SECURE.
  9. Ground connection - REMOVE.
  10. Fuel quantity - CHECK.