H-160/Appendices
1 APPENDIX A - CHAT COMMAND SUMMARY
1.1 Main Command Summary
| Command | Description |
|---|---|
| help | Get command summary NC |
| menu | Post the main menu |
| cycen | Center the cyclic |
| pedcen | Center the pedals |
| cv | Toggle camera view |
| cv2 | Overhead camera view |
| fc | Toggle fine control between normal and most recently used of fc1 and fc2 |
| dc | Close all doors |
| mlt | Toggle "mouse look touch" |
| qstart | Do a quick start (skip full start procedure) |
| qstop or stop | Do a quick shutdown (skip full shutdown procedure) |
| hud | Get copy of hud |
| minihud | Get copy of minihud |
| winchhud/hoisthud | Get copy of hoist hud (if equipped) |
| checklist | Bring out or stow the checklist |
| ec1+ | Advance engine control #1 forward |
| ec1- | Pull engine control #1 back |
| ec2+ | Advance engine control #2 forward |
| ec2- | Pull engine control #2 back |
| ec1/p | Move engine conrol #1 to position p where p is s for SHUT OFF, i for GROUND IDLE, or f for FULL OPEN |
| ec2/p | Move engine conrol #2 to position p where p is s for SHUT OFF, i for GROUND IDLE, or f for FULL OPEN |
| s switch-name | Toggle the switch named "switch-name" (see list of switches below) |
| s1 switch-name | Turn on the switch named "switch-name" |
| s0 switch-name | Turn off the switch named "switch-name" |
| sn switch-name | Set rotary switch position n. |
| ap cmd | Autopilot command |
| x cmd | Transponder command |
| gps cmd | GPS command |
| w cmd | Winch/Hoist command (if equipped) |
1.2 Switch Names
(used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches) This section describes the various switches in the CH-47 and their functions. Push buttons (marked with [b]), and rotary knobs (marked with [r]) are also shown here. Switches that are for RP purposes only and do not have an effect on the helicopter are marked [RP] in the description. For switches that have guards, the guard is addressed by appending a "-g" to the switch name (marked with [-g] after the name in the table below).
1.3 Autopilot Command Summary
The following chat commands can be used with the AFCS:
| Command | Description |
|---|---|
| ap IAS | Toggle airspeed hold |
| ap ALT | Toggle altitude hold |
| ap RALT | Toggle radar altitude hold |
| ap VS | Toggle vertical speed hold |
| ap HDG | Toggle heading hold |
| ap DIS | Disconnect autopilot |
| ap IAS n | Set the target airspeed to n |
| ap HDG n | Set the target heading to n |
| ap L n | Set the target heading left by n degrees |
| ap R n | Set the target heading right by n degrees |
| ap ALT n | Set the target altitude to n feet |
| ap RALT n | Set the target altitude to n feet above ground |
| ap VS n | Set the target vertical speed n feet per second |
| ap D n | Set target altitude up n feet |
| ap U n | Set target altitude down n feet |
| ap HVR | Enter autohover mode |
| ap TO | Takeoff and enter hover |
| ap LAND | Land at current location |
1.4 GPS Command Summary
The chat commands available for the FMS/GPS are:
| Command | Description |
|---|---|
| gps route wp1 wp2 ... wpn.app | Replace current route with specified route |
| gps new | Delete all waypoints |
| gps direct | Go direct to next waypoint |
| gps hold | Toggle hold at next waypoint |
| gps hsi | Toggle HSI mode between DTK and NAV |
| gps save [label] | Save the current route to server |
| gps load spec | Load a route from server |
1.5 Transponder Command Summary
The available transponder chat commands are:
| Command | Description |
|---|---|
| x nnnn | Enter four-digit transponder code. |
| x stby/on/alt | Set the transponder mode. |
2 APPENDIX B - SWITCH SUMMARY
2.1 GENERAL
This appendix includes the list of all switches and knobs in the helicopter. The switch names can be used to control the switches from chat commands or gestures. The chat commands for the various switch types are described below. Chat commands may be issued on local chat, or on the channel /2973 for use in gestures.
2.1.1 Toggle switches
Toggle switches (<xr id='fig:toggle'>) are simple two position switches, in most cases with an ON and OFF position (a small subset are selectors between two options). Commands for toggle switches are:
| Command | Description |
|---|---|
| s name | Toggle a switch |
| s1 name | Move a switch to the ON position. |
| s1 name | Move a switch to the OFF position. |
2.1.2 Rocker Switch
Tri-State/Rocker Switches The H-160 has a few three-state "rocker" style switches. The switch positions are numbered with "0" as the center position and "1" and "2" as the edge positions. Rockers are moved be clicking on one half of them. Each click moves it one position. Some rocker switches are "spring loaded" on one side or the other. For example the DG CORR switch shown here has LH, RH positions that are spring loaded to a center neutral position. They can be controlled with the following chat commands:
| Command | Description |
|---|---|
| s0 name | Move switch to center position |
| s1 name | Move switch to edge position 1 |
| s2 name | Move switch to edge position 2 |
Note that chat commands with spring-loaded switches will not automatically return to the center position. You must explicitly use an "s0" command after a delay. This is to allow you to control the delay in gestures.
2.1.3 Rotary Switches
Rotary switches have varying numbers of discrete positions and are controlled with a rotating knob. The positions are numbered starting with zero at the most counter-clockwise position and increase in a clockwise direction. For example in the knob shown in the figure to the left the BOTH setting is position 0, and the OFF setting is position 3. Knobs are moved interactively by clicking on them. The side on which you click, relative to the indicating line, determines the direction of rotation.
To set a rotary switch to positon n via chat command use:
sn name
2.1.4 List of Toggle and Tri-State Switches
| Name | Description |
|---|---|
| batt1 | Battery #1 |
| batt2 | Battery #2 |
| gen1 | Generator #1 |
| gen2 | Generator #2 |
| cutoff1 | DC1 Emergency Cutoff |
| cutoff2 | DC2 Emergency Cutoff |
| fadec1 | FADEC #1 |
| fadec2 | FADEC #2 |
| emergen | Emergency Generator |
| ice | Ice Detection |
| load | Load Selector |
| fms1 | Flight Management System #1 |
| fms2 | Flight Management System #1 |
| ra1 | Radar Altimeter #1 |
| ra2 | Radar Altimeter #2 |
| test | Warning Light Test |
| dgCorr | DG Correction |
| emerextn | Emergency Gear Extend |
| hyd[ts] | Hydraulic Mode |
| park | Parking Brake |
| fuelcut1 | Engine #1 Fuel Cutoff |
| fuelcut2 | Engine #2 Fuel Cutoff |
| elt | ELT Mode |
| mode[ts] | Engine Training Mode |
[ts]: Tri-state "rocker" switches
2.1.5 List of Rotary Switches
| Name | Description |
|---|---|
| mfd3 | MFD3 Display Mode |
| ahrs | Active AHRS Select |
| mission | Mission Select |
| float | Float Mode |
| wiper | Wipers |
| taws | TAWS Mode |
| ckptLts | Cockpit light brightness |
| instLts | Instrument lights |
| anticol | Anti-Collision ights |
| nav | Navigation/Position lights |
| ldg | Landing Lights |
| noseLock | Nosewheel lock |
| cabinLts | Main cabin lights |
