MD-500D/Maintenance and Diagnostics
SECTION 10. MAINTENANCE AND DIAGNOSTICS
Contents
1 General
The MD-500D has 14 replaceable components, each with an individually tracked service lifetime. Component lifetimes are measured as a function of the HOBBS time of the helicopter.
As a component ages, its failure rate increases, rising rapidly once its nominal service lifetime has expired. It is recommended that components be replaced at their prescribed service intervals.
In addition to component age, excess wear is tracked. Mishandling of the aircraft, such as exceeding operating limitations, may result in wear accumulation in affected components. Wear is not directly observable through normal inspection records but affects the failure rate of a component, potentially causing it to fail prematurely.
Component times, wear, and failure status are synchronized with the Shergood Aviation servers. Whenever an aircraft is rezzed, its component status is synchronized with the server. Component records are associated with the aircraft tail number, allowing multiple registered aircraft to maintain independent maintenance histories.
2 Component Failure Rates
Component failures are calculated individually according to a hazard rate function based on the age and accumulated wear of each component.
The hazard rate represents the instantaneous probability of failure per operating hour. Component wear is treated as additional effective age.
A new component has a very low, but nonzero, probability of failure. The failure rate increases as the component approaches its nominal service lifetime and rises rapidly after that lifetime has expired.
Consequently, a component may fail before its scheduled replacement interval, while another may continue operating beyond its prescribed lifetime. Continued operation beyond the service interval carries an increasing risk of failure.
The base hazard rate is modified by several factors:
- Failure Mode - A multiplier is applied according to the selected failure mode. Low, Medium, and High hazard multipliers are 0.25, 1.0, and 10.0 respectively.
- Fluid Levels - Operation with applicable fluid levels below 50% increases the failure rate of affected components and may cause additional wear.
- Misuse - Exceeding operating limitations, including excessive engine torque or rotor speed, increases the failure rate while the condition exists. Additional component wear may also accumulate.
Component wear persists until the affected component is replaced.
3 Failure and Fragile Modes
The handling of component failures and crash damage is controlled through the Failures and Fragile options in the aircraft @Option menu.
When Fragile mode is enabled, collisions and crashes may result in damage to the helicopter. When disabled, collision information may be reported without applying crash damage.
The Failures setting controls the occurrence of random failures and the accumulation of component wear.
| Mode | Description |
|---|---|
| None (N) | No failures or wear accumulation. Component operating times continue to accumulate normally. |
| Passive (P) | Direct damage and progression of existing failures remain active. Random failures and normal wear accumulation are disabled. |
| L1 (1) | Random failures, crash damage, and wear enabled. Failure rate is 10% of normal. |
| L2 (2) | Failure rate is 25% of normal. |
| L3 (3) | Failure rate is 50% of normal. |
| L4 (4) | Failure rate is 75% of normal. |
| L5 (5) | Normal failure rate. |
| L6 (6) | Failure rate is 1.5 times normal. |
| L7 (7) | Failure rate is 2 times normal. |
| L8 (8) | Failure rate is 5 times normal. |
| L9 (9) | Failure rate is 10 times normal. |
For modes L2 through L9, random failures, wear accumulation, and crash damage are enabled as described for L1.
4 Replaceable Components
The following table lists the 14 replaceable components and their nominal service lifetimes.
| Component | Lifetime (hours) |
|---|---|
| Engine Core | 100 |
| Main Rotor | 200 |
| Tail Rotor | 200 |
| Main Rotor Transmission | 150 |
| Tail Rotor Transmission | 150 |
| Generator/Starter | 20 |
| Fuel Filter | 20 |
| Fuel Pump | 30 |
| Starter Pump | 50 |
| Wiring Harness | 400 |
| Battery | 50 |
| Floats | 50 |
| Fuel Controller | 25 |
| Engine Air Particle Separator (EAPS) | 100 |
Component replacement is recommended when the prescribed lifetime is reached, or earlier if inspection or operational symptoms indicate a malfunction.
4.1 Failure Symptoms and Diagnostics
Component malfunctions may be indicated by warning lights, abnormal instrument readings, reduced system performance, or failure of an associated system to operate.
The following are general diagnostic indications associated with the installed systems.
| System | Possible Indications |
|---|---|
| Engine | ENGINE OUT or ENGINE CHIPS annunciator; abnormal engine RPM, torque, or TOT. |
| Main Rotor | Abnormal rotor response or inability to maintain normal rotor operation. |
| Tail Rotor | Reduced or lost directional control. |
| Main Rotor Transmission | XMSN OIL PRESS, XMSN OIL TEMP, or M/R XMSN CHIPS annunciator. |
| Tail Rotor Transmission | T/R XMSN CHIPS annunciator; abnormal tail rotor operation. |
| Generator/Starter | GEN OUT annunciator; failure to generate electrical power or engage the starter. |
| Fuel Filter | FUEL FILTER annunciator; possible restriction of fuel flow. |
| Fuel Pump | Abnormal fuel delivery or engine operation. |
| Starter Pump | Difficulty starting or maintaining required fuel pressure during starting. |
| Wiring Harness | Loss or intermittent operation of electrical equipment. |
| Battery | Reduced electrical capacity or inadequate engine starting performance. |
| Floats | Failure of the emergency flotation system to deploy or inflate correctly. |
| Fuel Controller | Unstable engine operation or abnormal fuel scheduling. |
| Engine Air Particle Separator | Reduced engine performance or abnormal engine inlet airflow. |
These indications may have multiple causes and do not necessarily identify a failed component conclusively.
5 Inspecting Components
Components may be inspected to determine their general condition.
Where supported, clicking a component produces an inspection message reflecting its age and accumulated wear.
The following condition descriptions correspond to the effective percentage of the component's service lifetime.
| Condition Message | Effective Lifetime |
|---|---|
| Appears to be in good condition | Less than 50% |
| Appears to be serviceable | 50%–75% |
| Appears to be well used | 75%–85% |
| Appears to be well worn | 85%–95% |
| Appears to be on its last legs | 95%–100% |
| Appears to have seen better days | 100%–150% |
| Appears as if it might break by looking at it wrong | Greater than 150% |
The effective lifetime includes the effects of accumulated wear. Consequently, a component may exhibit deterioration inconsistent with its recorded operating hours if it has been subjected to excessive operating stresses.
A component identified as damaged should be replaced before further operation.
6 Maintenance Workbench
The MD-500D is supplied with a maintenance workbench used to inspect and replace aircraft components.
Smaller components are arranged on the workbench, while larger assemblies, including the engine and rotor components, are positioned alongside the bench in shipping crates or on pallets.
The workbench also includes an aircraft maintenance logbook and a laptop computer for reviewing component maintenance records.
Clicking a replacement component when the workbench is not connected to an aircraft displays information identifying the component and its suitability for installation.
Clicking the workbench outside a component opens the maintenance control menu.
6.1 Connecting to a Helicopter
The maintenance workbench can connect to a helicopter within 20 meters.
- Position the maintenance workbench within 20 meters of the aircraft.
- Open the workbench control menu.
- Select CONNECT.
- Select the desired helicopter from the list of nearby aircraft.
- Verify that the correct aircraft tail number appears on the maintenance logbook and laptop.
The workbench will retrieve the component maintenance records for the selected aircraft.
6.2 Access Control
The workbench may be configured for owner-only or public use.
The Public option allows other users to operate the workbench. However, permission to operate the workbench does not automatically grant permission to maintain an aircraft.
The user performing maintenance must have the appropriate pilot privileges for the connected helicopter.
6.3 Maintenance Laptop
The maintenance laptop displays the current service records for the connected helicopter.
The laptop uses media-on-a-prim technology. Media must be enabled in the viewer to display the maintenance information.
The laptop displays the following information for each component:
| Field | Description |
|---|---|
| ID | Unique component identifier. |
| Component | Name of the installed component. |
| Service Time | Nominal service lifetime, in operating hours. |
| Install Date | Date and time of component installation. |
| Install HOBBS | Aircraft Hobbs meter reading at installation. |
| Remaining Time | Operating hours remaining before scheduled replacement. |
| Wear | Recorded accumulated wear of the component. |
Remaining service time is calculated from the component's installation Hobbs reading and the current aircraft Hobbs reading.
A negative remaining time indicates that the component has exceeded its nominal service interval.
The component list may be sorted by the available column headings to assist in identifying components approaching their replacement intervals.
6.4 Replacing Components
Replacement components are installed using the maintenance workbench.
Before replacing a component, the appropriate aircraft access panels must be opened to permit maintenance access.
- Park the helicopter and shut down the engine.
- Open the access panels required for the component being replaced.
- Connect the maintenance workbench to the helicopter.
- Inspect the component service records on the maintenance laptop.
- Locate the replacement component on the workbench.
- Click the replacement component.
- Confirm the installation when prompted.
- Verify that the maintenance laptop displays the updated component installation information.
- Replenish any required fluids.
- Close and secure all access panels.
If the required access panels are not open, the workbench may refuse installation and display an appropriate message.
Following successful installation, the component's service time is reset and its installation date and Hobbs reading are updated.
IMPORTANT NOTE: Replacement components are supplied without operating fluids. Components requiring lubrication must be serviced with the appropriate fluids before operation. Failure to do so may result in rapid wear or component failure.
6.5 Online Access to Component Records
Component maintenance records may also be viewed through the Shergood Aviation website.
To access the records:
- Log in to the Shergood Aviation website.
- Open your profile page.
- Select the My Aircraft tab.
- Select the desired aircraft by tail number.
- Open the Components tab.
The component records may also be accessed directly using the following URL, substituting the aircraft tail number for XXXXXX:
https://www.shergoodaviation.com/aircraft-status.php?n=XXXXXX
Access to component records is restricted to aircraft owned by the logged-in user.