H-92/General

From
< H-92
Revision as of 02:31, 3 August 2021 by Kelly (talk | contribs) (Created page with "<span class=sa-section>SECTION 1. GENERAL</span> === N-NUMBER ASSIGNMENT === When you rez your aircraft for the first time, it will attempt to contact registration server and...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

SECTION 1. GENERAL

1 N-NUMBER ASSIGNMENT

When you rez your aircraft for the first time, it will attempt to contact registration server and assign you a unique N-number. If for some reason the server cannot be contacted, the aircraft will retain the "N-TEMP" registration. You can attempt to register again either by rerezing the aircraft, or by going to the @REGISTER menu and selecting the [Register Now] button. When an aircraft has not been registered, the @REGISTER will be available on the main menu. Once the aircraft is registered, you can access the @REGISTER menu as a sub-menu of the @Admin menu. You can also request a different N-number through the @REGISTER menu. Select the [N Number] button and enter an N-Number request. The N-number must be in a valid format, and must not be assigned to another aircraft. Valid N-Numbers must begin with an "N", followed by 3 to 5 alpha-numeric digits (however, only the last two digits may be letters). Alternatively you can select one of the international registration formats L-LLLL or LL-LLL where the "L" are letters. Your distribution also comes with a registration certificate. You can use this to fetch and display your registration information, but its use is optional and not required to assign or change N-numbers for your aircraft.

2 CONTROLS

This aircraft supports two separate control schemes. Control scheme 1 features a traditional layout with the cyclic controlled by the arrow keys, whereas control scheme 2 features a "two handed" layout with either both hands on the keyboard, or left hand on keyboard and right hand on the mouse. Regardless of the scheme selected, controls can also be moved through the HUD by pressing and holding the left mouse button and dragging the appropriate slider in the HUD. In both control schemes, some key commands are activated through gestures included in a box as part of the product carton. Key commands requiring a gesture are marked with a [G] in the key command lists below.

2.1 CONTROLS LAYOUT "K" (KEYBOARD)

Keyboard control features a traditional layout with the cyclic controlled by the arrow keys.

Key Description
Left/Right/Up/Down (or A/D/W/S) Cyclic (Left/Right/Forward.Back)
PgUp/PgDown (or E/C) Collective (Up/Down)
R/V Throttle (Up/Down) [G]
L. Mouse + Left/Right (or A/D) Pedals (left/right)*
Shift-Left/Shift-Right Alternate pedal control (not available in mouselook)
Z/X Alternate pedal keys (left/right) [G]
. Center cyclic [G]
p Toggle camera view [G]
q Toggle fine control [G]
  • NOTE ON PEDALS: Because the left mouse button is intercepted by the touch scripts in the heli, the L.Mouse + Arrow key combination will only work in mouselook, or in external view modes. There is also a "mouselook touch" mode that is toggled by the "mlt" chat command. This toggles whether mouse clicks while in mouselook affect switches and buttons in the cockpit, or are used for pedals.

2.2 CONTROLS LAYOUT "H" (HUD OR TWO-HANDED KEYBOARD)

Key Description
Up/Down (or W/S) Collective (Up/Down)
Left/Right (or E/C) Anti-Torque Pedals
J/L/I/K Cyclic left/right/forward/back [G]
. Center cyclic [G]
p Toggle camera view [G]
q Toggle fine control [G]

3 CHAT COMMANDS

Command Description
help Get command summary NC
cycen Center the cyclic
cv Toggle camera view
cv2 Overhead camera view
fc Toggle fine control (smaller movement per key press)
mlt Toggle "mouse look touch"
hc Hoist control mode (aft pilot only)
qstart Do a quick start (skip full start procedure)
qstop Do a quick shutdown (skip full shutdown procedure)
hud Get copy of hud
poh Get copy of POH (Pilot Operating Handbook)
rb Toggle rotor break
rb0/rb1 Set rotor break off (rb0) or on (rb1)
g/gu/gd Landing gear (toggle/up/down)
ec1+ Advance engine control #1 forward
ec1- Pull engine control #1 back
ec2+ Advance engine control #2 forward
ec2- Pull engine control #2 back
ec1/p Move engine conrol #1 to position p where p is s for SHUT OFF, i for GROUND IDLE, or f for FULL OPEN
ec2/p Move engine conrol #2 to position p where p is s for SHUT OFF, i for GROUND IDLE, or f for FULL OPEN
s switch-name Toggle the switch named "switch-name" (see list of switches below)
s1 switch-name Turn on the switch named "switch-name"
s0 switch-name Turn off the switch named "switch-name"
sx switch-name Move switch to middle position for three position switches.
ap cmd Autopilot command (see AUTOPILOT section below)

4 SWITCH NAMES (used with s, s1 and s0 commands)

4.1 Core start-up switches

Switch Description
extPower Use external power
batt Battery power (powers battery bus)
apuGen APU Generator for main power bus
apuCtrl APU Control (turns APU on/off)
airSrce APU powered air source for starting main engines
ign-1 Engine #1 igniter
ign-2 Engine #2 igniter
fuel-1 Engine #1 fuel pump (3-position: OFF, XFD, DIRECT)
fuel-2 Engine #2 fuel pump (3-position: OFF, XFD, DIRECT)
starter-1 Engine #1 starter
starter-2 Engine #2 starter
acgen-1 Engine #1 AC generator
acgen-2 Engine #2 AC generator
dcconv-1 Engine #1 DC converter
dcconv-2 Engine #2 DC converter
dcconv-bak Backup DC converter

4.2 External Lights

Switch Description
uprAnitCol Upper Anti-Collision Light
lwrAntiCOl Lower Anti-Collision Light
fwdLdg-1 #1 (left) landing light
fwdLdg-2 #2 (right) landing light
posnLghts Position lights

4.3 Cockpit Lights

Switch Description
backupLght Backup cockpit lighting (red)
instLght Primary instrument lights
sideLght Cockpit side lighting
ovhdLght Overhead panel lights
lwrLght Lower panel lights
pbLght Floor flights
floodLght Cockpit flood lights

4.4 Cabin Lights

Switch Description
cabinOvhd Cabin overhead lights
seatBelt Cabin fasten seatbelt sign
noSmoke Cabin no smoking sign
cabinRead Enable passenger reading lights

4.5 Other

Switch Description
fireExt Arm fire extinguisher
elt Arm ELT
emergDn Enable emergency down of landing gear

5 AUTOPILOT

The autopilot supports the following chat commands:

Command Description
ap IAS Toggle airspeed hold
ap ALT Toggle altitude hold
ap HDG Toggle heading hold
ap V/S Toggle vertical speed hold
ap HVR Enter autohover mode
ap SEL Change "selected" parameter
ap + Increase value of selected parameter
ap - Decrease value of selected parameter
ap DIS Disconnect autopilot
ap IAS n Set the target airspeed to n
ap HDG n Set the target heading to n
ap L n Set the target heading left by n degrees
ap R n Set the target heading right by n degrees
ap ALT n Set the target altitude to n feet
ap U n Set the altitude up by n feet
ap D n Set the altitude down by n feet
ap V/S n Set the target vertical speed to n

See AFCS/Autopilot section below for details on autopilot operation.

6 CAMERA

The default camera position is inside the cockpit with a view through the front glass. It is also possible to switch to an outside "follow cam" view. Wear the "cameraViews" gestures and use the "p" key to toggle views. In addition, it is possible to fly in mouselook when using one of the keyboard based flight control methods.

7 FINE CONTROL

The "fc" chat command or "q" gesture command toggle fine control for key commands. While fine control is active, key commands will have half the effect the do in regular mode. This can be useful when higher precision is need such as for making an accurate landing on a small platform.