SECTION 13. APPENDICES
1 COMMAND SUMMARY
Command
|
Description
|
help
|
Get link to aircraft documentation.
|
menu
|
Post the main menu
|
cycen
|
Center the cyclic
|
pedcen
|
Center the pedals
|
cv/cv0/cv1/cv2/cv3
|
Change camera view: toggle/cockpit/behind/overhead/underside
|
fc/fc0/fc1/fc2
|
Fine control: toggle/off/fine/very-fine
|
dc
|
Close all doors
|
rb/rb0/rb1
|
Toggle rotor brake/Rotor brake on/Rotor brake off
|
mlt
|
Toggle "mouse look touch"
|
qstart
|
Do a quick start (skip full start procedure)
|
qstop or stop
|
Do a quick shutdown (skip full shutdown procedure)
|
hud
|
Get copy of hud
|
winchhud/hoisthud
|
Get copy of hoist hud
|
checklist
|
Bring out or stow the checklist
|
s switch-name
|
Toggle the switch named "switch-name"
|
s1 switch-name
|
Turn on the switch named "switch-name"
|
s0 switch-name
|
Turn off the switch named "switch-name"
|
sn switch-name
|
Set rotary or three position switch to position n.
|
com1 freq
|
Set the COM1 radio frequency to freq
|
com2 freq
|
Set the COM2 radio frequency to freq
|
hf freq
|
Set the HF radio frequency to freq
|
ap cmd
|
Autopilot command
|
x cmd
|
Transponder command
|
nav cmd
|
Navigation/VOR command
|
wind cmd
|
Set wind model for on-water behavior.
|
w cmd
|
Winch/Hoist command
|
wx cmd
|
Weather command
|
2 SWITCH SUMMARY
This section describes the various switches in the S-58 and their functions (used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches). Push buttons (marked with [b]), and rotary knobs (marked with [r]) are also shown here. Switches that are for RP purposes only and do not have an effect on the helicopter are marked [RP] in the description. For switches that have guards, the guard is addressed by appending a "-g" to the switch name (marked with [-g] after the name in the table below).
2.1 Switches
Name
|
Description
|
inv |
Inverter Select
|
oildil |
Oil Dillution
|
bstpmp |
Boost Pump
|
clutch |
Clutch Engagement
|
fuelcutoff |
Fuel Cut-off
|
elt [ts] |
ELT
|
fan |
Cabin fan
|
pitot |
Pitot heat
|
read |
Passenger Reading Lights
|
posbrt |
Position light brightness
|
alarm[-g] |
Crew alarm
|
beacon |
Beacon
|
sticktrim |
Stick Trim
|
cablecut[-g] |
Hoist cable cut (cockpit)
|
radio |
Radio master
|
elecbarr |
Electric barrier door
|
brake |
Parking Brake
|
taillock |
Tailwheel Lock
|
floodlts [ts] |
Flood and hover lights
|
hoist [ts] |
Hoist Mode
|
heat [ts] |
Cabin Heat
|
posmode [ts] |
Position light mode
|
cabinlts [ts] |
Main cabin lights
|
dcpwr [ts] |
DC Power
|
ckptdome [ts] |
Cockpit dome light
|
hook [ts] |
Cargo hook mode
|
ldglts [ts] |
Landing Lights
|
servo [ts] |
Servo Mode
|
cabCableCut[-g] |
Hoist Cable Cut (cabin)
|
l-com1 |
COM1 listen
|
l-com2 |
COM2 listen
|
l-nav1 |
NAV1 listen
|
l-nav2 |
NAV2 listen
|
l-hf |
HF listen
|
l-uhf |
UHF listen
|
2.2 Knobs
Name
|
Description
|
Positions
|
emerlts |
Instrument Emergency Lights |
0:off, 1-3:levels, 4:high
|
conalts |
Console A Panel Lights (copilot) |
0:off, 1-3:levels, 4:high
|
nonfltlts |
Non-Flight Instrument Lights |
0:off, 1-3:levels, 4:high
|
fltlts |
Flight Instrument Lights (pilot) |
0:off, 1-3:levels, 4:high
|
mags |
Magnetos/Ignition |
0:OFF, 1:L, 2:R, 4:BOTH
|
fuelsel |
Fuel Indicator Select |
0:TOT, 1:FWD, 2:CTR, 3:AFT
|
xpdr |
Transponder Mode |
0:off, 1:sby: 2:on, 3:alt, 4:tst
|
cgtrim |
CG Trim |
0:F3, 1:F2, 2:F1, 3:CTR, 4:A1, 5:A2, 6:A3
|
yawtrim |
Yaw Trim |
0:L4, 1:L3, 2:L2, 3:L1, 4:CTR, 5:R1, 6:R2, 7:R3, 8:R4
|
txsel |
Transmit Select |
0:COM1, 1:COM2, 2:HF, 3:UHF
|
wipers |
Windshield Wipers |
0:Park, 1:Off, 2:Fast, 3:Med, 4:Slow
|