H-160/Appendices

From
< H-160
Revision as of 02:19, 26 August 2021 by Kelly (talk | contribs) (Toggle switches)
Jump to: navigation, search

1 APPENDIX A - CHAT COMMAND SUMMARY

1.1 Main Command Summary

Command Description
help Get command summary NC
menu Post the main menu
cycen Center the cyclic
pedcen Center the pedals
cv Toggle camera view
cv2 Overhead camera view
fc Toggle fine control between normal and most recently used of fc1 and fc2
dc Close all doors
mlt Toggle "mouse look touch"
qstart Do a quick start (skip full start procedure)
qstop or stop Do a quick shutdown (skip full shutdown procedure)
hud Get copy of hud
minihud Get copy of minihud
winchhud/hoisthud Get copy of hoist hud (if equipped)
checklist Bring out or stow the checklist
ec1+ Advance engine control #1 forward
ec1- Pull engine control #1 back
ec2+ Advance engine control #2 forward
ec2- Pull engine control #2 back
ec1/p Move engine conrol #1 to position p where p is s for SHUT OFF, i for GROUND IDLE, or f for FULL OPEN
ec2/p Move engine conrol #2 to position p where p is s for SHUT OFF, i for GROUND IDLE, or f for FULL OPEN
s switch-name Toggle the switch named "switch-name" (see list of switches below)
s1 switch-name Turn on the switch named "switch-name"
s0 switch-name Turn off the switch named "switch-name"
sn switch-name Set rotary switch position n.
ap cmd Autopilot command
x cmd Transponder command
gps cmd GPS command
w cmd Winch/Hoist command (if equipped)

1.2 Switch Names

(used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches) This section describes the various switches in the CH-47 and their functions. Push buttons (marked with [b]), and rotary knobs (marked with [r]) are also shown here. Switches that are for RP purposes only and do not have an effect on the helicopter are marked [RP] in the description. For switches that have guards, the guard is addressed by appending a "-g" to the switch name (marked with [-g] after the name in the table below).

1.3 Autopilot Command Summary

The following chat commands can be used with the AFCS:

Command Description
ap IAS Toggle airspeed hold
ap ALT Toggle altitude hold
ap RALT Toggle radar altitude hold
ap VS Toggle vertical speed hold
ap HDG Toggle heading hold
ap DIS Disconnect autopilot
ap IAS n Set the target airspeed to n
ap HDG n Set the target heading to n
ap L n Set the target heading left by n degrees
ap R n Set the target heading right by n degrees
ap ALT n Set the target altitude to n feet
ap RALT n Set the target altitude to n feet above ground
ap VS n Set the target vertical speed n feet per second
ap D n Set target altitude up n feet
ap U n Set target altitude down n feet
ap HVR Enter autohover mode
ap TO Takeoff and enter hover
ap LAND Land at current location

1.4 GPS Command Summary

The chat commands available for the FMS/GPS are:

Command Description
gps route wp1 wp2 ... wpn.app Replace current route with specified route
gps new Delete all waypoints
gps direct Go direct to next waypoint
gps hold Toggle hold at next waypoint
gps hsi Toggle HSI mode between DTK and NAV
gps save [label] Save the current route to server
gps load spec Load a route from server

1.5 Transponder Command Summary

The available transponder chat commands are:

Command Description
x nnnn Enter four-digit transponder code.
x stby/on/alt Set the transponder mode.

2 APPENDIX B - SWITCH SUMMARY

2.1 GENERAL

This appendix includes the list of all switches and knobs in the helicopter. The switch names can be used to control the switches from chat commands or gestures. The chat commands for the various switch types are described below. Chat commands may be issued on local chat, or on the channel /2973 for use in gestures.

2.1.1 Toggle switches
Figure 1: Toggle Switch

Toggle switches (<xr id='fig:toggle'>) are simple two position switches, in most cases with an ON and OFF position (a small subset are selectors between two options). Commands for toggle switches are:

Command Description
s name Toggle a switch
s1 name Move a switch to the ON position.
s1 name Move a switch to the OFF position.
2.1.2 Rocker Switch

Tri-State/Rocker Switches The H-160 has a few three-state "rocker" style switches. The switch positions are numbered with "0" as the center position and "1" and "2" as the edge positions. Rockers are moved be clicking on one half of them. Each click moves it one position. Some rocker switches are "spring loaded" on one side or the other. For example the DG CORR switch shown here has LH, RH positions that are spring loaded to a center neutral position. They can be controlled with the following chat commands:

Command Description
s0 name Move switch to center position
s1 name Move switch to edge position 1
s2 name Move switch to edge position 2

Note that chat commands with spring-loaded switches will not automatically return to the center position. You must explicitly use an "s0" command after a delay. This is to allow you to control the delay in gestures.

2.1.3 Rotary Switches

Rotary switches have varying numbers of discrete positions and are controlled with a rotating knob. The positions are numbered starting with zero at the most counter-clockwise position and increase in a clockwise direction. For example in the knob shown in the figure to the left the BOTH setting is position 0, and the OFF setting is position 3. Knobs are moved interactively by clicking on them. The side on which you click, relative to the indicating line, determines the direction of rotation.

To set a rotary switch to positon n via chat command use:

sn name
2.1.4 List of Toggle and Tri-State Switches
Name Description
batt1 Battery #1
batt2 Battery #2
gen1 Generator #1
gen2 Generator #2
cutoff1 DC1 Emergency Cutoff
cutoff2 DC2 Emergency Cutoff
fadec1 FADEC #1
fadec2 FADEC #2
emergen Emergency Generator
ice Ice Detection
load Load Selector
fms1 Flight Management System #1
fms2 Flight Management System #1
ra1 Radar Altimeter #1
ra2 Radar Altimeter #2
test Warning Light Test
dgCorr DG Correction
emerextn Emergency Gear Extend
hyd[ts] Hydraulic Mode
park Parking Brake
fuelcut1 Engine #1 Fuel Cutoff
fuelcut2 Engine #2 Fuel Cutoff
elt ELT Mode
mode[ts] Engine Training Mode

[ts]: Tri-state "rocker" switches

2.1.5 List of Rotary Switches
Name Description
mfd3 MFD3 Display Mode
ahrs Active AHRS Select
mission Mission Select
float Float Mode
wiper Wipers
taws TAWS Mode
ckptLts Cockpit light brightness
instLts Instrument lights
anticol Anti-Collision ights
nav Navigation/Position lights
ldg Landing Lights
noseLock Nosewheel lock
cabinLts Main cabin lights