H-34 Choctaw/Appendices

SECTION 13. APPENDICES

1 COMMAND SUMMARY

Command	Description
help	Get link to aircraft documentation.
menu	Post the main menu
cycen	Center the cyclic
pedcen	Center the pedals
cv/cv0/cv1/cv2/cv3	Change camera view: toggle/cockpit/behind/overhead/underside
fc/fc0/fc1/fc2	Fine control: toggle/off/fine/very-fine
dc	Close all doors
rb/rb0/rb1	Toggle rotor brake/Rotor brake on/Rotor brake off
mlt	Toggle "mouse look touch"
qstart	Do a quick start (skip full start procedure)
qstop or stop	Do a quick shutdown (skip full shutdown procedure)
hud	Get copy of hud
winchhud/hoisthud	Get copy of hoist hud
checklist	Bring out or stow the checklist
s switch-name	Toggle the switch named "switch-name"
s1 switch-name	Turn on the switch named "switch-name"
s0 switch-name	Turn off the switch named "switch-name"
sn switch-name	Set rotary or three position switch to position n.
com1 freq	Set the COM1 radio frequency to freq
com2 freq	Set the COM2 radio frequency to freq
hf freq	Set the HF radio frequency to freq
ap cmd	Autopilot command
x cmd	Transponder command
nav cmd	Navigation/VOR command
w cmd	Winch/Hoist command
wx cmd	Weather command

1.1 Autopilot Commands

Regular ASE Commands:

Command	Description
ap eng	Hold the current airspeed and heading.
ap alt	Hold the current altitude. The ENG channel must already be engaged for altitude hold to be engaged.
ap dis	Disconnect the ASE.

Extended ASE Commands (must be enabled in @Realism menu):

Command	Description
ap hdg n	Turn to heading n.
ap r n	Turn right by n degrees.
ap l n	Turn left by n degrees.
ap u n	Move up n feet.
ap d n	Move down n feet.
ap hvr	Enter autohover mode.
ap to	Take off to a hover.
ap land	Autoland the aircraft.

2 SWITCH SUMMARY

This section describes the various switches in the S-58 and their functions (used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches). Push buttons (marked with [b]), and rotary knobs (marked with [r]) are also shown here. Switches that are for RP purposes only and do not have an effect on the helicopter are marked [RP] in the description. For switches that have guards, the guard is addressed by appending a "-g" to the switch name (marked with [-g] after the name in the table below).

2.1 Switches

Name	Description
inv	Inverter Select
oildil	Oil Dillution
bstpmp	Boost Pump
clutch	Clutch Engagement
fuelcutoff	Fuel Cut-off
elt [ts]	ELT
fan	Cabin fan
pitot	Pitot heat
read	Passenger Reading Lights
posbrt	Position light brightness
alarm[-g]	Crew alarm
beacon	Beacon
sticktrim	Stick Trim
cablecut[-g]	Hoist cable cut (cockpit)
radio	Radio master
elecbarr	Electric barrier door
brake	Parking Brake
taillock	Tailwheel Lock
floodlts [ts]	Flood and hover lights
hoist [ts]	Hoist Mode
heat [ts]	Cabin Heat
posmode [ts]	Position light mode
cabinlts [ts]	Main cabin lights
dcpwr [ts]	DC Power
ckptdome [ts]	Cockpit dome light
hook [ts]	Cargo hook mode
ldglts [ts]	Landing Lights
servo [ts]	Servo Mode
cabCableCut[-g]	Hoist Cable Cut (cabin)
l-com1	COM1 listen
l-com2	COM2 listen
l-nav1	NAV1 listen
l-nav2	NAV2 listen
l-hf	HF listen
l-uhf	UHF listen

2.2 Knobs

Name	Description	Positions
emerlts	Instrument Emergency Lights	0:off, 1-3:levels, 4:high
conalts	Console A Panel Lights (copilot)	0:off, 1-3:levels, 4:high
nonfltlts	Non-Flight Instrument Lights	0:off, 1-3:levels, 4:high
fltlts	Flight Instrument Lights (pilot)	0:off, 1-3:levels, 4:high
mags	Magnetos/Ignition	0:OFF, 1:L, 2:R, 4:BOTH
fuelsel	Fuel Indicator Select	0:TOT, 1:FWD, 2:CTR, 3:AFT
xpdr	Transponder Mode	0:off, 1:sby: 2:on, 3:alt, 4:tst
cgtrim	CG Trim	0:F3, 1:F2, 2:F1, 3:CTR, 4:A1, 5:A2, 6:A3
yawtrim	Yaw Trim	0:L4, 1:L3, 2:L2, 3:L1, 4:CTR, 5:R1, 6:R2, 7:R3, 8:R4
txsel	Transmit Select	0:COM1, 1:COM2, 2:HF, 3:UHF
wipers	Windshield Wipers	0:Park, 1:Off, 2:Fast, 3:Med, 4:Slow