Difference between revisions of "H-34 Choctaw/Appendices"
(→SWITCH SUMMARY) |
(→COMMAND SUMMARY) |
||
| Line 78: | Line 78: | ||
|nav ''cmd'' | |nav ''cmd'' | ||
|Navigation/VOR command | |Navigation/VOR command | ||
| − | |||
| − | |||
| − | |||
|- | |- | ||
|w ''cmd'' | |w ''cmd'' | ||
| Line 88: | Line 85: | ||
|Weather command | |Weather command | ||
|} | |} | ||
| + | |||
| + | ==== Autopilot Commands ==== | ||
| + | ==== Transponder Commands ==== | ||
| + | ==== Navigation Commands ==== | ||
| + | ==== Weather Commands ==== | ||
=== SWITCH SUMMARY === | === SWITCH SUMMARY === | ||
Revision as of 14:30, 10 September 2021
SECTION 13. APPENDICES
Contents
1 COMMAND SUMMARY
| Command | Description |
|---|---|
| help | Get link to aircraft documentation. |
| menu | Post the main menu |
| cycen | Center the cyclic |
| pedcen | Center the pedals |
| cv/cv0/cv1/cv2/cv3 | Change camera view: toggle/cockpit/behind/overhead/underside |
| fc/fc0/fc1/fc2 | Fine control: toggle/off/fine/very-fine |
| dc | Close all doors |
| rb/rb0/rb1 | Toggle rotor brake/Rotor brake on/Rotor brake off |
| mlt | Toggle "mouse look touch" |
| qstart | Do a quick start (skip full start procedure) |
| qstop or stop | Do a quick shutdown (skip full shutdown procedure) |
| hud | Get copy of hud |
| winchhud/hoisthud | Get copy of hoist hud |
| checklist | Bring out or stow the checklist |
| s switch-name | Toggle the switch named "switch-name" |
| s1 switch-name | Turn on the switch named "switch-name" |
| s0 switch-name | Turn off the switch named "switch-name" |
| sn switch-name | Set rotary or three position switch to position n. |
| com1 freq | Set the COM1 radio frequency to freq |
| com2 freq | Set the COM2 radio frequency to freq |
| hf freq | Set the HF radio frequency to freq |
| ap cmd | Autopilot command |
| x cmd | Transponder command |
| nav cmd | Navigation/VOR command |
| w cmd | Winch/Hoist command |
| wx cmd | Weather command |
1.1 Autopilot Commands
1.2 Transponder Commands
1.4 Weather Commands
2 SWITCH SUMMARY
This section describes the various switches in the S-58 and their functions (used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches). Push buttons (marked with [b]), and rotary knobs (marked with [r]) are also shown here. Switches that are for RP purposes only and do not have an effect on the helicopter are marked [RP] in the description. For switches that have guards, the guard is addressed by appending a "-g" to the switch name (marked with [-g] after the name in the table below).
2.1 Switches
| Name | Description |
|---|---|
| inv | Inverter Select |
| oildil | Oil Dillution |
| bstpmp | Boost Pump |
| clutch | Clutch Engagement |
| fuelcutoff | Fuel Cut-off |
| elt [ts] | ELT |
| fan | Cabin fan |
| pitot | Pitot heat |
| read | Passenger Reading Lights |
| posbrt | Position light brightness |
| alarm[-g] | Crew alarm |
| beacon | Beacon |
| sticktrim | Stick Trim |
| cablecut[-g] | Hoist cable cut (cockpit) |
| radio | Radio master |
| elecbarr | Electric barrier door |
| brake | Parking Brake |
| taillock | Tailwheel Lock |
| floodlts [ts] | Flood and hover lights |
| hoist [ts] | Hoist Mode |
| heat [ts] | Cabin Heat |
| posmode [ts] | Position light mode |
| cabinlts [ts] | Main cabin lights |
| dcpwr [ts] | DC Power |
| ckptdome [ts] | Cockpit dome light |
| hook [ts] | Cargo hook mode |
| ldglts [ts] | Landing Lights |
| servo [ts] | Servo Mode |
| cabCableCut[-g] | Hoist Cable Cut (cabin) |
| l-com1 | COM1 listen |
| l-com2 | COM2 listen |
| l-nav1 | NAV1 listen |
| l-nav2 | NAV2 listen |
| l-hf | HF listen |
| l-uhf | UHF listen |
2.2 Knobs
| Name | Description | Positions |
|---|---|---|
| emerlts | Instrument Emergency Lights | 0:off, 1-3:levels, 4:high |
| conalts | Console A Panel Lights (copilot) | 0:off, 1-3:levels, 4:high |
| nonfltlts | Non-Flight Instrument Lights | 0:off, 1-3:levels, 4:high |
| fltlts | Flight Instrument Lights (pilot) | 0:off, 1-3:levels, 4:high |
| mags | Magnetos/Ignition | 0:OFF, 1:L, 2:R, 4:BOTH |
| fuelsel | Fuel Indicator Select | 0:TOT, 1:FWD, 2:CTR, 3:AFT |
| xpdr | Transponder Mode | 0:off, 1:sby: 2:on, 3:alt, 4:tst |
| cgtrim | CG Trim | 0:F3, 1:F2, 2:F1, 3:CTR, 4:A1, 5:A2, 6:A3 |
| yawtrim | Yaw Trim | 0:L4, 1:L3, 2:L2, 3:L1, 4:CTR, 5:R1, 6:R2, 7:R3, 8:R4 |
| txsel | Transmit Select | 0:COM1, 1:COM2, 2:HF, 3:UHF |
| wipers | Windshield Wipers | 0:Park, 1:Off, 2:Fast, 3:Med, 4:Slow |
