Difference between revisions of "MD-500D/Normal Procedures"

From
Jump to: navigation, search
(→‎Normal Startup)
(→‎= Start Checks)
Line 50: Line 50:
 
#Rotors - CLEARED
 
#Rotors - CLEARED
  
−
===== Start Checks ====
+
<div style="border: 2px solid red; padding: 10px;">
 
CAUTION: During starts, overtemps above 810C for 10 sec. or less with a momentary peak at 927C for not more than 1 sec. are permitted. Consult Operation and Maint. Manual if these limits are exceeded.
 
CAUTION: During starts, overtemps above 810C for 10 sec. or less with a momentary peak at 927C for not more than 1 sec. are permitted. Consult Operation and Maint. Manual if these limits are exceeded.
  
−
ABORT START IF:
+
ABORT START IF:<br />
−
TOT indicator – no immediate rise
+
#TOT indicator – no immediate rise
−
Oil Press – no indication
+
#Oil Press – no indication
−
Main rotor – not rotating by 25% N1
+
#Main rotor – not rotating by 25% N1
−
Ammeter – zero or positive indication
+
#Ammeter – zero or positive indication
  
−
Abort start procedures
+
Abort start procedures<br />
−
Close twistgrip to CUTOFF position
+
#Close twistgrip to CUTOFF position
−
Use starter to continue motoring engine for at least 10 seconds or until TOT decreases below 150C
+
#Use starter to continue motoring engine for at least 10 seconds or until TOT decreases below 150C
 +
</div>
  
 
==== Engine Start ====
 
==== Engine Start ====

Revision as of 02:59, 21 November 2026

SECTION 4. NORMAL PROCEDURES

1 General

This section describes the procedures necessary to safely and efficiently operate your aircraft. A basic understanding of helicopter flight techniques is assumed.

1.1 Preflight Procedures

1.2 Normal Startup

1.2.1 Electrical Power - OFF

  1. Cabin Doors - CLOSED
  2. Cyclic, collective - FULL TRAVEL
  3. Cyclic - NEUTRAL
  4. Pedals - NEUTRAL
  5. Collective - FULL DOWN
  6. Landing Light - OFF
  7. Air Filter Bypass - CHECK POSITION
  8. Vne Card - SELECT
  9. Instrument Static Position - CHECK
  10. Altimeter - SET
  11. Electrical Switches – OFF

1.2.2 Electrical Power - ON

  1. Electrical: Battery or external power start
  2. BATTERY/EXR PWR switch: set to BATTERY for battery start; to EXT for external power start - AS REQUIRED

If used, connect GPU Lights - AS REQUIRED

  1. Key switch - ON
  2. Engine Out Warning System/Auto Reignition System Checks
  3. GEN switch ON then OFF to check audible engine out warnings
  4. Hold AUTO RE-IGN TEST switch in the TEST position. Verify the RE-IGN and ARMED lights illuminate, and the sound of the engine ignitor firing is heard. Release the AUTO RE-IGN TEST switch.
  5. Press the RE-IGN light to reset (extinguish) light.
  6. Fuel gauge - CHECK
  7. All other instruments - CHECK
  8. XMSN OIL PRESS, ENGINE OUT and GEN warning lights - CHECK ON
  9. Press-to-test caution/warning lights - CHECK
  10. Throttle twist grip to FULL OPEN, then return to CUTOFF - CHECK

1.2.3 Pre-Start

  1. Cyclic centered - RECHECK
  2. Collective full down - RECHECK
  3. Twistgrip in CUTOFF position - RECHECK
  4. Generator switch OFF - RECHECK
  5. Start pump - AS REQUIRED

NOTE: Start pump required when using alternate of emergency fuel

  1. Rotors - CLEARED

CAUTION: During starts, overtemps above 810C for 10 sec. or less with a momentary peak at 927C for not more than 1 sec. are permitted. Consult Operation and Maint. Manual if these limits are exceeded.

ABORT START IF:

  1. TOT indicator – no immediate rise
  2. Oil Press – no indication
  3. Main rotor – not rotating by 25% N1
  4. Ammeter – zero or positive indication

Abort start procedures

  1. Close twistgrip to CUTOFF position
  2. Use starter to continue motoring engine for at least 10 seconds or until TOT decreases below 150C

1.2.4 Engine Start

  1. Start/ignition button - PRESS

Note: Do not motor starter more than 60 seconds without ignition occurring. Cool down 60 seconds after 1st and 2nd attempt, and 30 minutes after 3rd attempt.

  1. Rotate twistgrip to ground idle for ignition when N1 indicates 12% to 15%

NOTE: Peaking of N1 below 15% may occur during cold weather starting conditions. Under these conditions, a start may be attempted at a minimum of 12% N1. GPU starts are recommended when normal cranking speed cannot be obtained by using the battery.

  1. Start button - RELEASE at 58% to 60% N1
  2. Oil pressure 50 to 130 psi - CHECK

NOTE: During cold weather operation, 150 psi oil pressure is allowable following an engine start. Remain at ground idle RPM until normal oil pressure limits are attained.

  1. All caution/warning indicators out - CHECK
NOTE: Transmission oil pressure warning (XMSN OIL PRESS) will go out within 30 seconds from engine light-off
  1. Engine idle speed - 64% to 65% N1 - CHECK
  2. All other engine instruments - CHECK
  3. N2 engine and rotor rpm indicator needles superimposed - CHECK
  4. Start pump - AS REQUIRED

1.2.5 Engine Run-Up

  1. Electrical Power – SELECT
  2. Select BATT
  3. Ext Power - Disconnect (if used)
  4. Generator – ON
  5. Avionics – CHECK
  6. Twist Grip – FULL OPEN
  7. Press RE-IGN – CHECK OUT
  8. N2 high beep 104% - 105% - CHECK
  9. N2 low beep 98% - CHECK
  10. Low rotor warning at 98% - CHECK
  11. RE-IGN light – CHECK ON
  12. N2 beep – SET 102%
  13. Press RE-IGN – CHECK OUT
  14. Throttle rigging check
  15. N2 102% - CHECK
  16. Twistgrip – SNAP TO IDLE
  17. If engine flameout – ABORT FLIGHT
  18. Twistgrip – FULL OPEN
  19. N2 102% - CHECK

1.3 Pre Takeoff Checks

Caution/warning lights - OUT Engine oil pressure - 90 to 130 Ammeter - CHECK READING All cabin doors – CLOSED All instruments – IN GREEN Position/anti-collision lights - AS REQUIRED SCAV AIR - AS DESIRED Takeoff Hover area and takeoff path - CLEAR N2 – 103% Height/Velocity Profile – FOLLOW

1.4 Cruise Checks

SCAV AIR - AS DESIRED

1.5 Pre-Landing Checks

Pre-Landing N2 – 103% SCAV AIR – AS DESIRED

1.6 Shutdown Procedures

Engine Shutdown Collective Stick - FULL DOWN Twistgrip –IDLE (hold for 2 minutes) Note: check for NR/N2 needle split immediately after throttle cut. All unnecessary electrical equipment - OFF Pedals - CENTERED Twistgrip - CUTOFF Engine out warning at 55% N1 - CHECK Auto reignition light – ON Generator switch - OFF NAV/COM Switches - OFF All other switches - OFF BATTERY/EXTERNAL PWR switch - OFF Key switch - OFF