Difference between revisions of "MD-500D/Normal Procedures"
< MD-500D
(→Shutdown Procedures) |
|||
| (17 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | <span class=sa-section>SECTION | + | <span class=sa-section>SECTION 6. NORMAL PROCEDURES</span> |
== General == | == General == | ||
| Line 10: | Line 10: | ||
=== Normal Startup === | === Normal Startup === | ||
| − | Electrical Power - OFF | + | ==== Electrical Power - OFF ==== |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | #Cabin Doors - CLOSED | |
| − | + | #Cyclic, collective - FULL TRAVEL | |
| − | + | #Cyclic - NEUTRAL | |
| − | + | #Pedals - NEUTRAL | |
| − | + | #Collective - FULL DOWN | |
| − | + | #Landing Light - OFF | |
| − | + | #Air Filter Bypass - CHECK POSITION | |
| − | + | #Vne Card - SELECT | |
| − | + | #Instrument Static Position - CHECK | |
| + | #Altimeter - SET | ||
| + | #Electrical Switches – OFF | ||
| − | + | ==== Electrical Power - ON ==== | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| + | #Electrical: Battery or external power start | ||
| + | #* BATTERY/EXR PWR switch: | ||
| + | #*: set to BATTERY for battery start | ||
| + | #*: set to EXT for external power start | ||
| + | #* If used, connect GPU | ||
| + | # Lights - AS REQUIRED | ||
| + | #Key switch - ON | ||
| + | #Engine Out Warning System/Auto Reignition System Checks | ||
| + | #* GEN switch ON then OFF to check audible engine out warnings | ||
| + | #* Hold AUTO RE-IGN TEST switch in the TEST position. Verify the RE-IGN and ARMED lights illuminate, and the sound of the engine ignitor firing is heard. Release the AUTO RE-IGN TEST switch. | ||
| + | #Press the RE-IGN light to reset (extinguish) light. | ||
| + | #Fuel gauge - CHECK | ||
| + | #All other instruments - CHECK | ||
| + | #XMSN OIL PRESS, ENGINE OUT and GEN warning lights - CHECK ON | ||
| + | #Press-to-test caution/warning lights - CHECK | ||
| + | #Throttle twist grip to FULL OPEN, then return to CUTOFF - CHECK | ||
| + | ==== Pre-Start ==== | ||
| + | #Cyclic centered - RECHECK | ||
| + | #Collective full down - RECHECK | ||
| + | #Twistgrip in CUTOFF position - RECHECK | ||
| + | #Generator switch OFF - RECHECK | ||
| + | #Start pump - AS REQUIRED | ||
| + | #: NOTE: Start pump required when using alternate of emergency fuel | ||
| + | #Rotors - CLEARED | ||
| + | |||
| + | <div style="border: 2px solid red; padding: 10px;"> | ||
CAUTION: During starts, overtemps above 810C for 10 sec. or less with a momentary peak at 927C for not more than 1 sec. are permitted. Consult Operation and Maint. Manual if these limits are exceeded. | CAUTION: During starts, overtemps above 810C for 10 sec. or less with a momentary peak at 927C for not more than 1 sec. are permitted. Consult Operation and Maint. Manual if these limits are exceeded. | ||
| − | ABORT START IF: | + | ABORT START IF:<br /> |
| − | TOT indicator – no immediate rise | + | #TOT indicator – no immediate rise |
| − | Oil Press – no indication | + | #Oil Press – no indication |
| − | Main rotor – not rotating by 25% N1 | + | #Main rotor – not rotating by 25% N1 |
| − | Ammeter – zero or positive indication | + | #Ammeter – zero or positive indication |
| − | Abort start procedures | + | Abort start procedures<br /> |
| − | Close twistgrip to CUTOFF position | + | #Close twistgrip to CUTOFF position |
| − | Use starter to continue motoring engine for at least 10 seconds or until TOT decreases below 150C | + | #Use starter to continue motoring engine for at least 10 seconds or until TOT decreases below 150C |
| + | </div> | ||
| − | Engine Start | + | ==== Engine Start ==== |
| − | Start/ignition button - PRESS | + | #Start/ignition button - PRESS |
| − | Note: Do not motor starter more than 60 seconds without ignition | + | #: Note: Do not motor starter more than 60 seconds without ignition occurring. Cool down 60 seconds after 1st and 2nd attempt, and 30 minutes after 3rd attempt. |
| − | Rotate twistgrip to ground idle for ignition when N1 indicates 12% to 15% | + | # Rotate twistgrip to ground idle for ignition when N1 indicates 12% to 15% |
| − | NOTE: Peaking of N1 below 15% may occur during cold weather starting conditions. Under these conditions, a start may be attempted at a minimum of 12% N1. GPU starts are recommended when normal cranking speed cannot be obtained by using the battery. | + | #: NOTE: Peaking of N1 below 15% may occur during cold weather starting conditions. Under these conditions, a start may be attempted at a minimum of 12% N1. GPU starts are recommended when normal cranking speed cannot be obtained by using the battery. |
| − | Start button - RELEASE at 58% to 60% N1 | + | # Start button - RELEASE at 58% to 60% N1 |
| − | Oil pressure 50 to 130 psi - CHECK | + | #Oil pressure 50 to 130 psi - CHECK |
| − | NOTE: During cold weather operation, 150 psi oil pressure is allowable following an engine start. Remain at ground idle RPM until normal oil pressure limits are attained. | + | #: NOTE: During cold weather operation, 150 psi oil pressure is allowable following an engine start. Remain at ground idle RPM until normal oil pressure limits are attained. |
| + | #All caution/warning indicators out - CHECK | ||
| + | #: NOTE: Transmission oil pressure warning (XMSN OIL PRESS) will go out within 30 seconds from engine light-off | ||
| + | #Engine idle speed - 64% to 65% N1 - CHECK | ||
| + | #All other engine instruments - CHECK | ||
| + | #N2 engine and rotor rpm indicator needles superimposed - CHECK | ||
| + | #Start pump - AS REQUIRED | ||
| − | Engine | + | ==== Engine Run-Up ==== |
| − | + | #Electrical Power – SELECT | |
| − | + | #* Select BATT | |
| − | + | #* Ext Power - Disconnect (if used) | |
| − | + | #Generator – ON | |
| − | N2 | + | #Avionics – CHECK |
| − | + | #Twist Grip – FULL OPEN | |
| + | #Press RE-IGN – CHECK OUT | ||
| + | #N2 high beep 104% - 105% - CHECK | ||
| + | #N2 low beep 98% - CHECK | ||
| + | #Low rotor warning at 98% - CHECK | ||
| + | #RE-IGN light – CHECK ON | ||
| + | #N2 beep – SET 102% | ||
| + | #Press RE-IGN – CHECK OUT | ||
| + | #Throttle rigging check | ||
| + | ## N2 102% - CHECK | ||
| + | ## Twistgrip – SNAP TO IDLE | ||
| + | ## If engine flameout – ABORT FLIGHT | ||
| + | ## Twistgrip – FULL OPEN | ||
| + | ## N2 102% - CHECK | ||
| − | + | === Pre Takeoff Checks === | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | # Caution/warning lights - OUT | |
| + | #Engine oil pressure - 90 to 130 | ||
| + | #Ammeter - CHECK READING | ||
| + | #All cabin doors – CLOSED | ||
| + | #All instruments – IN GREEN | ||
| + | #Position/anti-collision lights - AS REQUIRED | ||
| + | #SCAV AIR - AS DESIRED | ||
| − | + | === Takeoff === | |
| − | + | #Hover area and takeoff path - CLEAR | |
| − | + | #N2 – 103% | |
| − | + | #Height/Velocity Profile – FOLLOW | |
| − | |||
| − | |||
| − | |||
| − | Takeoff | ||
| − | Hover area and takeoff path - CLEAR | ||
| − | N2 – 103% | ||
| − | Height/Velocity Profile – FOLLOW | ||
=== Cruise Checks === | === Cruise Checks === | ||
| − | SCAV AIR - AS DESIRED | + | #SCAV AIR - AS DESIRED |
=== Pre-Landing Checks === | === Pre-Landing Checks === | ||
| − | Pre-Landing | + | #Pre-Landing |
| − | N2 – 103% | + | #N2 – 103% |
| − | SCAV AIR – AS DESIRED | + | #SCAV AIR – AS DESIRED |
=== Shutdown Procedures === | === Shutdown Procedures === | ||
| − | Engine Shutdown | + | #Engine Shutdown |
| − | Collective Stick - FULL DOWN | + | #Collective Stick - FULL DOWN |
| − | Twistgrip –IDLE (hold for 2 minutes) | + | #Twistgrip –IDLE (hold for 2 minutes) |
| − | Note: check for NR/N2 needle split immediately after throttle cut. | + | #: Note: check for NR/N2 needle split immediately after throttle cut. |
| − | All unnecessary electrical equipment - OFF | + | # All unnecessary electrical equipment - OFF |
| − | Pedals - CENTERED | + | # Pedals - CENTERED |
| − | Twistgrip - CUTOFF | + | #Twistgrip - CUTOFF |
| − | Engine out warning at 55% N1 - CHECK | + | #Engine out warning at 55% N1 - CHECK |
| − | Auto reignition light – ON | + | #Auto reignition light – ON |
| − | Generator switch - OFF | + | #Generator switch - OFF |
| − | NAV/COM Switches - OFF | + | #NAV/COM Switches - OFF |
| − | All other switches - OFF | + | #All other switches - OFF |
| − | BATTERY/EXTERNAL PWR switch - OFF | + | #BATTERY/EXTERNAL PWR switch - OFF |
| − | Key switch - OFF | + | #Key switch - OFF |
Latest revision as of 03:12, 21 November 2026
SECTION 6. NORMAL PROCEDURES
Contents
1 General
This section describes the procedures necessary to safely and efficiently operate your aircraft. A basic understanding of helicopter flight techniques is assumed.
1.1 Preflight Procedures
1.2 Normal Startup
1.2.1 Electrical Power - OFF
- Cabin Doors - CLOSED
- Cyclic, collective - FULL TRAVEL
- Cyclic - NEUTRAL
- Pedals - NEUTRAL
- Collective - FULL DOWN
- Landing Light - OFF
- Air Filter Bypass - CHECK POSITION
- Vne Card - SELECT
- Instrument Static Position - CHECK
- Altimeter - SET
- Electrical Switches – OFF
1.2.2 Electrical Power - ON
- Electrical: Battery or external power start
- BATTERY/EXR PWR switch:
- set to BATTERY for battery start
- set to EXT for external power start
- If used, connect GPU
- BATTERY/EXR PWR switch:
- Lights - AS REQUIRED
- Key switch - ON
- Engine Out Warning System/Auto Reignition System Checks
- GEN switch ON then OFF to check audible engine out warnings
- Hold AUTO RE-IGN TEST switch in the TEST position. Verify the RE-IGN and ARMED lights illuminate, and the sound of the engine ignitor firing is heard. Release the AUTO RE-IGN TEST switch.
- Press the RE-IGN light to reset (extinguish) light.
- Fuel gauge - CHECK
- All other instruments - CHECK
- XMSN OIL PRESS, ENGINE OUT and GEN warning lights - CHECK ON
- Press-to-test caution/warning lights - CHECK
- Throttle twist grip to FULL OPEN, then return to CUTOFF - CHECK
1.2.3 Pre-Start
- Cyclic centered - RECHECK
- Collective full down - RECHECK
- Twistgrip in CUTOFF position - RECHECK
- Generator switch OFF - RECHECK
- Start pump - AS REQUIRED
- NOTE: Start pump required when using alternate of emergency fuel
- Rotors - CLEARED
CAUTION: During starts, overtemps above 810C for 10 sec. or less with a momentary peak at 927C for not more than 1 sec. are permitted. Consult Operation and Maint. Manual if these limits are exceeded.
ABORT START IF:
- TOT indicator – no immediate rise
- Oil Press – no indication
- Main rotor – not rotating by 25% N1
- Ammeter – zero or positive indication
Abort start procedures
- Close twistgrip to CUTOFF position
- Use starter to continue motoring engine for at least 10 seconds or until TOT decreases below 150C
1.2.4 Engine Start
- Start/ignition button - PRESS
- Note: Do not motor starter more than 60 seconds without ignition occurring. Cool down 60 seconds after 1st and 2nd attempt, and 30 minutes after 3rd attempt.
- Rotate twistgrip to ground idle for ignition when N1 indicates 12% to 15%
- NOTE: Peaking of N1 below 15% may occur during cold weather starting conditions. Under these conditions, a start may be attempted at a minimum of 12% N1. GPU starts are recommended when normal cranking speed cannot be obtained by using the battery.
- Start button - RELEASE at 58% to 60% N1
- Oil pressure 50 to 130 psi - CHECK
- NOTE: During cold weather operation, 150 psi oil pressure is allowable following an engine start. Remain at ground idle RPM until normal oil pressure limits are attained.
- All caution/warning indicators out - CHECK
- NOTE: Transmission oil pressure warning (XMSN OIL PRESS) will go out within 30 seconds from engine light-off
- Engine idle speed - 64% to 65% N1 - CHECK
- All other engine instruments - CHECK
- N2 engine and rotor rpm indicator needles superimposed - CHECK
- Start pump - AS REQUIRED
1.2.5 Engine Run-Up
- Electrical Power – SELECT
- Select BATT
- Ext Power - Disconnect (if used)
- Generator – ON
- Avionics – CHECK
- Twist Grip – FULL OPEN
- Press RE-IGN – CHECK OUT
- N2 high beep 104% - 105% - CHECK
- N2 low beep 98% - CHECK
- Low rotor warning at 98% - CHECK
- RE-IGN light – CHECK ON
- N2 beep – SET 102%
- Press RE-IGN – CHECK OUT
- Throttle rigging check
- N2 102% - CHECK
- Twistgrip – SNAP TO IDLE
- If engine flameout – ABORT FLIGHT
- Twistgrip – FULL OPEN
- N2 102% - CHECK
1.3 Pre Takeoff Checks
- Caution/warning lights - OUT
- Engine oil pressure - 90 to 130
- Ammeter - CHECK READING
- All cabin doors – CLOSED
- All instruments – IN GREEN
- Position/anti-collision lights - AS REQUIRED
- SCAV AIR - AS DESIRED
1.4 Takeoff
- Hover area and takeoff path - CLEAR
- N2 – 103%
- Height/Velocity Profile – FOLLOW
1.5 Cruise Checks
- SCAV AIR - AS DESIRED
1.6 Pre-Landing Checks
- Pre-Landing
- N2 – 103%
- SCAV AIR – AS DESIRED
1.7 Shutdown Procedures
- Engine Shutdown
- Collective Stick - FULL DOWN
- Twistgrip –IDLE (hold for 2 minutes)
- Note: check for NR/N2 needle split immediately after throttle cut.
- All unnecessary electrical equipment - OFF
- Pedals - CENTERED
- Twistgrip - CUTOFF
- Engine out warning at 55% N1 - CHECK
- Auto reignition light – ON
- Generator switch - OFF
- NAV/COM Switches - OFF
- All other switches - OFF
- BATTERY/EXTERNAL PWR switch - OFF
- Key switch - OFF