Difference between revisions of "MD-500D/Normal Procedures"
(→Cruise Checks) |
(→Pre Takeoff Checks) |
||
| Line 102: | Line 102: | ||
## N2 102% - CHECK | ## N2 102% - CHECK | ||
| − | + | === Pre Takeoff Checks === | |
# Caution/warning lights - OUT | # Caution/warning lights - OUT | ||
Revision as of 03:10, 21 November 2026
SECTION 4. NORMAL PROCEDURES
Contents
1 General
This section describes the procedures necessary to safely and efficiently operate your aircraft. A basic understanding of helicopter flight techniques is assumed.
1.1 Preflight Procedures
1.2 Normal Startup
1.2.1 Electrical Power - OFF
- Cabin Doors - CLOSED
- Cyclic, collective - FULL TRAVEL
- Cyclic - NEUTRAL
- Pedals - NEUTRAL
- Collective - FULL DOWN
- Landing Light - OFF
- Air Filter Bypass - CHECK POSITION
- Vne Card - SELECT
- Instrument Static Position - CHECK
- Altimeter - SET
- Electrical Switches – OFF
1.2.2 Electrical Power - ON
- Electrical: Battery or external power start
- BATTERY/EXR PWR switch:
- set to BATTERY for battery start
- set to EXT for external power start
- If used, connect GPU
- BATTERY/EXR PWR switch:
- Lights - AS REQUIRED
- Key switch - ON
- Engine Out Warning System/Auto Reignition System Checks
- GEN switch ON then OFF to check audible engine out warnings
- Hold AUTO RE-IGN TEST switch in the TEST position. Verify the RE-IGN and ARMED lights illuminate, and the sound of the engine ignitor firing is heard. Release the AUTO RE-IGN TEST switch.
- Press the RE-IGN light to reset (extinguish) light.
- Fuel gauge - CHECK
- All other instruments - CHECK
- XMSN OIL PRESS, ENGINE OUT and GEN warning lights - CHECK ON
- Press-to-test caution/warning lights - CHECK
- Throttle twist grip to FULL OPEN, then return to CUTOFF - CHECK
1.2.3 Pre-Start
- Cyclic centered - RECHECK
- Collective full down - RECHECK
- Twistgrip in CUTOFF position - RECHECK
- Generator switch OFF - RECHECK
- Start pump - AS REQUIRED
- NOTE: Start pump required when using alternate of emergency fuel
- Rotors - CLEARED
CAUTION: During starts, overtemps above 810C for 10 sec. or less with a momentary peak at 927C for not more than 1 sec. are permitted. Consult Operation and Maint. Manual if these limits are exceeded.
ABORT START IF:
- TOT indicator – no immediate rise
- Oil Press – no indication
- Main rotor – not rotating by 25% N1
- Ammeter – zero or positive indication
Abort start procedures
- Close twistgrip to CUTOFF position
- Use starter to continue motoring engine for at least 10 seconds or until TOT decreases below 150C
1.2.4 Engine Start
- Start/ignition button - PRESS
- Note: Do not motor starter more than 60 seconds without ignition occurring. Cool down 60 seconds after 1st and 2nd attempt, and 30 minutes after 3rd attempt.
- Rotate twistgrip to ground idle for ignition when N1 indicates 12% to 15%
- NOTE: Peaking of N1 below 15% may occur during cold weather starting conditions. Under these conditions, a start may be attempted at a minimum of 12% N1. GPU starts are recommended when normal cranking speed cannot be obtained by using the battery.
- Start button - RELEASE at 58% to 60% N1
- Oil pressure 50 to 130 psi - CHECK
- NOTE: During cold weather operation, 150 psi oil pressure is allowable following an engine start. Remain at ground idle RPM until normal oil pressure limits are attained.
- All caution/warning indicators out - CHECK
- NOTE: Transmission oil pressure warning (XMSN OIL PRESS) will go out within 30 seconds from engine light-off
- Engine idle speed - 64% to 65% N1 - CHECK
- All other engine instruments - CHECK
- N2 engine and rotor rpm indicator needles superimposed - CHECK
- Start pump - AS REQUIRED
1.2.5 Engine Run-Up
- Electrical Power – SELECT
- Select BATT
- Ext Power - Disconnect (if used)
- Generator – ON
- Avionics – CHECK
- Twist Grip – FULL OPEN
- Press RE-IGN – CHECK OUT
- N2 high beep 104% - 105% - CHECK
- N2 low beep 98% - CHECK
- Low rotor warning at 98% - CHECK
- RE-IGN light – CHECK ON
- N2 beep – SET 102%
- Press RE-IGN – CHECK OUT
- Throttle rigging check
- N2 102% - CHECK
- Twistgrip – SNAP TO IDLE
- If engine flameout – ABORT FLIGHT
- Twistgrip – FULL OPEN
- N2 102% - CHECK
1.3 Pre Takeoff Checks
- Caution/warning lights - OUT
- Engine oil pressure - 90 to 130
- Ammeter - CHECK READING
- All cabin doors – CLOSED
- All instruments – IN GREEN
- Position/anti-collision lights - AS REQUIRED
- SCAV AIR - AS DESIRED
1.3.1 Takeoff
- Hover area and takeoff path - CLEAR
- N2 – 103%
- Height/Velocity Profile – FOLLOW
1.3.2 Cruise Checks
- SCAV AIR - AS DESIRED
1.4 Pre-Landing Checks
Pre-Landing N2 – 103% SCAV AIR – AS DESIRED
1.5 Shutdown Procedures
Engine Shutdown Collective Stick - FULL DOWN Twistgrip –IDLE (hold for 2 minutes) Note: check for NR/N2 needle split immediately after throttle cut. All unnecessary electrical equipment - OFF Pedals - CENTERED Twistgrip - CUTOFF Engine out warning at 55% N1 - CHECK Auto reignition light – ON Generator switch - OFF NAV/COM Switches - OFF All other switches - OFF BATTERY/EXTERNAL PWR switch - OFF Key switch - OFF