S-92/Normal Procedures - Revision history

Kelly at 01:15, 3 August 2021

2021-08-03T01:15:12Z

Kelly: /* Takeoff and Climb */

2021-08-03T01:06:15Z

‎Takeoff and Climb

Kelly: /* Shut-Down */

2021-08-03T01:05:27Z

‎Shut-Down

Kelly: /* Engine #2 Start */

2021-08-03T01:03:55Z

‎Engine #2 Start

Kelly: /* Engine #1 Start */

2021-08-03T00:58:56Z

‎Engine #1 Start

Kelly: Created page with "=== Start-Up === ====APU Start==== #Battery ON #Select EICAS on an MFD #Verify battery voltage at 28V (V-B). #APU GEN ON #APU CTL ON #APU AIR SRC ON #Verify primary bus (V-P..."

2021-08-03T00:58:14Z

Created page with "=== Start-Up === ====APU Start==== #Battery ON #Select EICAS on an MFD #Verify battery voltage at 28V (V-B). #APU GEN ON #APU CTL ON #APU AIR SRC ON #Verify primary bus (V-P..."

New page

=== Start-Up ===

====APU Start====

#Battery ON
#Select EICAS on an MFD
#Verify battery voltage at 28V (V-B).
#APU GEN ON
#APU CTL ON
#APU AIR SRC ON
#Verify primary bus (V-P) voltage at 28V
#Verify adequate fuel

====System Checks====

#Verify MSTR CAUTION, #1 ENG OUT and #2 ENG OUT warning lights ON
#Lift collective slightly, verify horn and LOW RPM warning
#Rotor break OFF
#Anti-Col. ON (Upr and Lwr)
#Position Lights ON for night flight

====Engine #1 Start====

# #1 Ignition (IGN) ON
# #1 Fuel to DIRECT
# #1 Engine Control to IDLE
#Press and hold #1 Start
#Verify Engine #1 N1 at least 20%
#Verify Engine #1 N1 increase to 100%.
#AC Generator #1 ON
#DC Converter #1 ON

← Older revision		Revision as of 01:15, 3 August 2021
Line 1:		Line 1:
		+	<span class=sa-section>SECTION 4. NORMAL PROCEDRUES</span>
		+
	=== Start-Up ===		=== Start-Up ===

@@ Line 59: / Line 59: @@
 #Verify caution lights OFF
 #Fly
 ==== Takeoff and Climb ====

@@ Line 76: / Line 76: @@
 #Up collective and left pedal to transition to hover
-====Shut-Down====
+===Shut-Down===
 # #1 and #2 engine controls to IDLE

← Older revision		Revision as of 01:03, 3 August 2021
Line 41:		Line 41:
	#AC Generator #2 ON		#AC Generator #2 ON
	#DC Converter #2 ON		#DC Converter #2 ON
		+
		+	====APU Shutdown and Emergency Systems====
		+
		+	#APU AIR SRC OFF
		+	#APU CTL OFF
		+	#APU GEN OFF
		+	#FIRE EXTG ARM
		+	#ELT ARM
		+
		+	==== Flight Preparations ====
		+
		+	#Verify DOORS CLOSED
		+	#Turn on Fasten Seatbelts
		+	#Increase #1 and #2 Engine Control to FLY
		+	#Verify Engine #1 and #2 N1 and N2 at 100%
		+	#Verify rotor RPM at 100%
		+	#Verify caution lights OFF
		+	#Fly
		+
		+	==== Takeoff and Climb ====
		+
		+	#Pull collective until aircraft lifts into hover. Apply left pedal to maintain directional control.
		+	#Apply forward cyclic and up collective for desired climb profile.
		+	#Landing gear UP
		+	#Slight down collective to level off. Control airspeed with cyclic.
		+	#Seat Belt Sign OFF
		+
		+	====Decent and Landing====
		+
		+	#Landing gear DOWN
		+	#Seat Belt Sign ON
		+	#Lower collective to begin decent and apply back cyclic to maintain 60-80kts
		+	#Nearing approach point, up collective and back cyclic to slow descent and approach rate
		+	#Up collective and left pedal to transition to hover
		+
		+	====Shut-Down====
		+
		+	# #1 and #2 engine controls to IDLE
		+	# Allow rotor RPM to stabilize
		+	# #1 and #2 engine controls to OFF
		+	#Rotor break ON when RPM below 50%
		+	#All switches OFF

← Older revision		Revision as of 00:58, 3 August 2021
Line 30:		Line 30:
	#AC Generator #1 ON		#AC Generator #1 ON
	#DC Converter #1 ON		#DC Converter #1 ON
		+
		+	====Engine #2 Start====
		+
		+	# #2 Ignition (IGN) ON
		+	# #2 Fuel to DIRECT
		+	# #2 Engine Control to IDLE
		+	#Verify Engine #2 N1 at least 20%
		+	#Press and hold #2 Start
		+	#Verify Engine #2 N1 increase to 100%
		+	#AC Generator #2 ON
		+	#DC Converter #2 ON