S-61R Pelican/All Weather Operations - Revision history

Kelly: /* Cabin Heat */

2022-01-02T14:58:09Z

‎Cabin Heat

Kelly: /* Weather in the S-61 */

2022-01-01T05:22:26Z

‎Weather in the S-61

Kelly: /* Utility Systems */

2022-01-01T05:21:00Z

‎Utility Systems

Kelly at 05:20, 1 January 2022

2022-01-01T05:20:09Z

Kelly: Created page with "SECTION 12. ALL-WEATHER OPERATIONS"

2022-01-01T05:18:34Z

Created page with "<span class=sa-section>SECTION 12. ALL-WEATHER OPERATIONS</span>"

New page

<span class=sa-section>SECTION 12. ALL-WEATHER OPERATIONS</span>

@@ Line 27: / Line 27: @@
 ==== Cabin Heat ====
-(RP Only) The cabin heat switches are located in the ice protection subpanel.  Left left two-position switch under CABIN HEATER has positions ON and VENT.  When in the VENT position, the heater is disabled and only air venting is enabled.  When the switch is in the ON position, the heater will operate at LOW, NORM (normal) or HIGH power depending on the three-position switch next to the ON/VENT switch.
+The cabin heat switches are located in the ice protection subpanel.  Left left two-position switch under CABIN HEATER has positions ON and VENT.  When in the VENT position, the heater is disabled and only air venting is enabled.  When the switch is in the ON position, the heater will operate at LOW, NORM (normal) or HIGH power depending on the three-position switch next to the ON/VENT switch.
 === Windshield Washer ===

@@ Line 9: / Line 9: @@
 ]]
-==== Ice Protection ====
+=== Ice Protection ===
 Ice protection systems are controlled through a panel on the overhead console (see <xr id='fig:antiice'/>).  These systems are described in the following sections.
-===== Engine Anti-Ice =====
+==== Engine Anti-Ice ====
 The engine anti-ice systems is comprised of a set of sensors and heaters in each engine inlet.  The purpose of the system is to prevent ice from forming at the engine inlets and possibly being ingested by them.  When the anti-ice system is engaged, the #1/#2 ENG-IVE ANTI-ICE advisory light for the affected engine will illuminate.  Also, while the anti-ice system is engaged, and the inlet temperature is below 38C, the #1/#2 INLET ANTI-ICE warning light will illuminate.  When first turning on the anti-ice switch, the #1/#2 INLET ANTI-ICE warning light may illuminate until the inlet surface temperatures warm up above 38C.  It is also possible for the #1/#2 INLET ANTI-ICE warning lights to come on in extremely cold temperatures if the inlet surfaces cannot be warmed above 38C.  The anti-ice system for the #1 engine operates off the #1 AC bus, while the anti-ice system for the #2 engine operates of the #2 AC bus.  The engine anti-ice system should be engaged with the OAT is below 5C.
-===== Windshield Anti-Ice =====
+==== Windshield Anti-Ice ====
 A windshield anti-ice switch labeled WINDSHIELD ANTI-ICE with positions LOW, OFF and HIGH positions is located as part of the ICE PROTECTION subpanel.  The system provides ice protection to the pilot and co-pilot sides of the windshield.  The co-pilot side anti-ice system is powered by the #1 AC bus while the pilot side anti-ice system is powered by the #2 AC bus.
-===== Pitot Heat =====
+==== Pitot Heat ====
 A pitot heat switch labeled PITOT HEAT with positions OFF and ON positions is located as part of the ICE PROTECTION subpanel. The system provides ice protection to the pilot and co-pilot pitot tubes. The co-pilot side anti-ice system is powered by the #1 AC bus while the pilot side anti-ice system is powered by the #2 AC bus.
-===== Cabin Heat =====
+==== Cabin Heat ====
 (RP Only) The cabin heat switches are located in the ice protection subpanel.  Left left two-position switch under CABIN HEATER has positions ON and VENT.  When in the VENT position, the heater is disabled and only air venting is enabled.  When the switch is in the ON position, the heater will operate at LOW, NORM (normal) or HIGH power depending on the three-position switch next to the ON/VENT switch.
-==== Windshield Washer ====
+=== Windshield Washer ===
 [[File:s61-wiperwasher.png|thumb|right|150px|
@@ Line 37: / Line 37: @@
 (RP Only) A windshield washer switch labeled WSHLD WASH controls the windshield washer fluid.
-==== Windshield Wipers ====
+=== Windshield Wipers ===
 The windshield wipers are controlled by a knob on the upper console (see <xr id='fig:wiperwasher' />) labeled WSHLD WIPER with positions OFF, LOW and HIGH.  The windshield wiper system is powered by the #1 AC bus.

@@ Line 1: / Line 1: @@
 <span class=sa-section>SECTION 12. ALL-WEATHER OPERATIONS</span>
-=== Utility Systems ===
+=== Weather in the S-61 ===
 [[File:s61-anti-ice.png|thumb|right|150px|
 <figure id="fig:antiice"><caption>Ice Protection</caption></figure>

← Older revision		Revision as of 05:20, 1 January 2022
Line 1:		Line 1:
	<span class=sa-section>SECTION 12. ALL-WEATHER OPERATIONS</span>		<span class=sa-section>SECTION 12. ALL-WEATHER OPERATIONS</span>
		+
		+	=== Utility Systems ===
		+	[[File:s61-anti-ice.png\|thumb\|right\|150px\|
		+	<figure id="fig:antiice"><caption>Ice Protection</caption></figure>
		+	]]
		+
		+	==== Ice Protection ====
		+
		+	Ice protection systems are controlled through a panel on the overhead console (see <xr id='fig:antiice'/>). These systems are described in the following sections.
		+
		+	===== Engine Anti-Ice =====
		+
		+	The engine anti-ice systems is comprised of a set of sensors and heaters in each engine inlet. The purpose of the system is to prevent ice from forming at the engine inlets and possibly being ingested by them. When the anti-ice system is engaged, the #1/#2 ENG-IVE ANTI-ICE advisory light for the affected engine will illuminate. Also, while the anti-ice system is engaged, and the inlet temperature is below 38C, the #1/#2 INLET ANTI-ICE warning light will illuminate. When first turning on the anti-ice switch, the #1/#2 INLET ANTI-ICE warning light may illuminate until the inlet surface temperatures warm up above 38C. It is also possible for the #1/#2 INLET ANTI-ICE warning lights to come on in extremely cold temperatures if the inlet surfaces cannot be warmed above 38C. The anti-ice system for the #1 engine operates off the #1 AC bus, while the anti-ice system for the #2 engine operates of the #2 AC bus. The engine anti-ice system should be engaged with the OAT is below 5C.
		+
		+	===== Windshield Anti-Ice =====
		+
		+	A windshield anti-ice switch labeled WINDSHIELD ANTI-ICE with positions LOW, OFF and HIGH positions is located as part of the ICE PROTECTION subpanel. The system provides ice protection to the pilot and co-pilot sides of the windshield. The co-pilot side anti-ice system is powered by the #1 AC bus while the pilot side anti-ice system is powered by the #2 AC bus.
		+
		+	===== Pitot Heat =====
		+
		+	A pitot heat switch labeled PITOT HEAT with positions OFF and ON positions is located as part of the ICE PROTECTION subpanel. The system provides ice protection to the pilot and co-pilot pitot tubes. The co-pilot side anti-ice system is powered by the #1 AC bus while the pilot side anti-ice system is powered by the #2 AC bus.
		+
		+	===== Cabin Heat =====
		+
		+	(RP Only) The cabin heat switches are located in the ice protection subpanel. Left left two-position switch under CABIN HEATER has positions ON and VENT. When in the VENT position, the heater is disabled and only air venting is enabled. When the switch is in the ON position, the heater will operate at LOW, NORM (normal) or HIGH power depending on the three-position switch next to the ON/VENT switch.
		+
		+	==== Windshield Washer ====
		+
		+	[[File:s61-wiperwasher.png\|thumb\|right\|150px\|
		+	<figure id="fig:wiperwasher"><caption>Windshield Wiper and Washer Controls</caption></figure>
		+	]]
		+
		+	(RP Only) A windshield washer switch labeled WSHLD WASH controls the windshield washer fluid.
		+
		+	==== Windshield Wipers ====
		+
		+	The windshield wipers are controlled by a knob on the upper console (see <xr id='fig:wiperwasher' />) labeled WSHLD WIPER with positions OFF, LOW and HIGH. The windshield wiper system is powered by the #1 AC bus.