View source for H-34 Choctaw/Appendices

<span class=sa-section>SECTION 13. APPENDICES</span>

=== COMMAND SUMMARY ===

{| class=wikitable
!Command	
!Description
|-
|help
|Get link to aircraft documentation.
|-
|menu
|Post the main menu
|-
|cycen
|Center the cyclic
|-
|pedcen
|Center the pedals
|-
|cv/cv0/cv1/cv2/cv3
|Change camera view: toggle/cockpit/behind/overhead/underside
|-
|fc/fc0/fc1/fc2
|Fine control: toggle/off/fine/very-fine
|-
|dc
|Close all doors
|-
|rb/rb0/rb1
|Toggle rotor brake/Rotor brake on/Rotor brake off
|-
|mlt
|Toggle "mouse look touch"
|-
|qstart
|Do a quick start (skip full start procedure)
|-
|qstop or stop
|Do a quick shutdown (skip full shutdown procedure)
|-
|hud
|Get copy of hud
|-
|winchhud/hoisthud
|Get copy of hoist hud
|-
|checklist
|Bring out or stow the checklist
|-
|s ''switch-name''
|Toggle the switch named "switch-name"
|-
|s1 ''switch-name''
|Turn on the switch named "switch-name"
|-
|s0 ''switch-name''
|Turn off the switch named "switch-name"
|-
|s''n'' ''switch-name''
|Set rotary or three position switch to position n.
|-
|com1 ''freq''
|Set the COM1 radio frequency to ''freq''
|-
|com2 ''freq''
|Set the COM2 radio frequency to ''freq''
|-
|hf ''freq''
|Set the HF radio frequency to ''freq''
|-
|ap ''cmd''
|Autopilot command
|-
|x ''cmd''
|Transponder command
|-
|nav ''cmd''
|Navigation/VOR command
|-
|wind ''cmd''
|Set wind model for on-water behavior.
|-
|w ''cmd''
|Winch/Hoist command
|-
|wx ''cmd''
|Weather command
|}

=== SWITCH SUMMARY ===

This section describes the various switches in the S-58 and their functions (used with s, s1 and s0 commands for normal switches s0, s1, s2, etc. for rotary switches). Push buttons (marked with [b]), and rotary knobs (marked with [r]) are also shown here. Switches that are for RP purposes only and do not have an effect on the helicopter are marked [RP] in the description. For switches that have guards, the guard is addressed by appending a "-g" to the switch name (marked with [-g] after the name in the table below).

==== Switches ====

{| class=wikitable
!Name
!Description
|-
|inv||Inverter Select
|-
|oildil||Oil Dillution
|-
|bstpmp||Boost Pump
|-
|clutch||Clutch Engagement
|-
|fuelcutoff||Fuel Cut-off
|-
|elt [ts]||ELT
|-
|fan||Cabin fan
|-
|pitot||Pitot heat
|-
|read||Passenger Reading Lights
|-
|posbrt||Position light brightness
|-
|alarm[-g]||Crew alarm
|-
|beacon||Beacon
|-
|sticktrim||Stick Trim
|-
|cablecut[-g]||Hoist cable cut (cockpit)
|-
|radio||Radio master
|-
|elecbarr||Electric barrier door
|-
|brake||Parking Brake
|-
|taillock||Tailwheel Lock
|-
|floodlts [ts]||Flood and hover lights
|-
|hoist [ts]||Hoist Mode
|-
|heat [ts]||Cabin Heat
|-
|posmode [ts]||Position light mode
|-
|cabinlts [ts]||Main cabin lights
|-
|dcpwr [ts]||DC Power
|-
|ckptdome [ts]||Cockpit dome light
|-
|hook [ts]||Cargo hook mode
|-
|ldglts [ts]||Landing Lights
|-
|servo [ts]||Servo Mode
|-
|cabCableCut[-g]||Hoist Cable Cut (cabin)
|-
|l-com1||COM1 listen
|-
|l-com2||COM2 listen
|-
|l-nav1||NAV1 listen
|-
|l-nav2||NAV2 listen
|-
|l-hf||HF listen
|-
|l-uhf||UHF listen
|}

==== Knobs ====

{| class=wikitable
!Name
!Description
!Positions
|-
|emerlts||Instrument Emergency Lights || 0:off, 1-3:levels, 4:high
|-
|conalts||Console A Panel Lights (copilot) || 0:off, 1-3:levels, 4:high
|-
|nonfltlts||Non-Flight Instrument Lights || 0:off, 1-3:levels, 4:high
|-
|fltlts||Flight Instrument Lights (pilot) || 0:off, 1-3:levels, 4:high
|-
|mags||Magnetos/Ignition || 0:OFF, 1:L, 2:R, 4:BOTH
|-
|fuelsel||Fuel Indicator Select || 0:TOT, 1:FWD, 2:CTR, 3:AFT
|-
|xpdr||Transponder Mode || 0:off, 1:sby: 2:on, 3:alt, 4:tst
|-
|cgtrim||CG Trim || 0:F3, 1:F2, 2:F1, 3:CTR, 4:A1, 5:A2, 6:A3
|-
|yawtrim||Yaw Trim || 0:L4, 1:L3, 2:L2, 3:L1, 4:CTR, 5:R1, 6:R2, 7:R3, 8:R4
|-
|txsel||Transmit Select || 0:COM1, 1:COM2, 2:HF, 3:UHF
|-
|wipers||Windshield Wipers || 0:Park, 1:Off, 2:Fast, 3:Med, 4:Slow
|}